Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I'm using an NRF51822 with soft device s110 version 7.1.0 and I'm having timer-related issues.
I create 1 periodic timer and 6 non-periodic (single shot) timers with app_timer_create...
Hello guys,
Hope someone can help me here. I am working with the NRF52 and want to use Zephyr . I am able to flash it. Using the nrf52 as periphal does not cause problems...
Hi,
I'm using SDK13.
I'm tring to save big size data (about 10KB) into flash when received them with 20 bytes pieces.
I called fds_record_write() in NUS's data handler...
Hi, I'm new to wireshark, and I want to filter all those empty pdus, they make it really hard for me to find the useful packets.
I tried btle.lendgth != 0, but got an error...
So I'm basing this off of the ble_app_hrs that initially has heart rates service and battery service. I want to create my own custom service andcopied the project to use as...
Hello,
I tested the example project "custom serial chat" from Atmel and wanted to see which Handle is used to send and receive data from Smartphone to the BLE-Board (SAMD21...
Hi.
I am designing PCB based on NRF51822-QFAA-R7.
There is 2450BM14E0003T balun will be used.
Here is reference design for that pair (NRF51822 + 2450BM14E0003T):
www...
I would like to register a bug report with the nRF5 SDK version 12.2.0. If you look at the example code in the SDK you will find that every example has a different build configuration...
We have a project which need to control the distance between the slave and the master to be less than 10m, say 5m. We tried -20 and found it a little longer than we expected...
How can I trasfer 20bytes data per 10ms?
Currently, I set gap_conn_params.min_conn_interval 7.5ms, and use BLE_EVT_TX_COMPLETE to send data. However, Android APP nrf Connect...
[Aim]
I am working on a project where I aimed to Integrate/Develop firmware management system using Contiki running over Nordic NRF52.
[Components]
Contiki running over...
On a nRF52832...
I'm trying to create a DFU package to update an existing SDK 11 SD2.0.0 firmware, to update it to SDK 12 SD + new application + secure bootloader
But the...
Hi
I am using SDK 12.3.0 with softdevice s130 v2. When I try to combine ble_app_hrs_peripheral code with app_uart.c, uart module gives error NRF_DRV_UART_EVT_ERROR in uart_irq_handler...
