In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
I prototyped a nRF52832, WLCSP package, with a fab (PCBA) and put jumpers between my 32Mhz crystal and the chip, attempting to connect with a j-link in SWA mode, I cannot...
Hi. I'm using nrf52832.
Now I'm using HFXO, LFXO to operate BLE. As I know I should use HFXO to operate BLE.
What about LFXO? Can I use internal clock(LFRC RC osc) instead...
Hi,
I am working on the latest version of SDK (v14) and SoftDevice(v5) on nRF52382. When I call the sd_gap_disconnect it returns NRF_SUCCESS. However the BLE_GAP_DISCONNECT...
I was trying to verify the DFU functionality on SDK 14 on nRF52832. Here is what I did.
1. Using nRFgo to erase all
2. Program bootloader/soft device with C:\svn\nordic...
Hi,
I am using SDK v12.2 and gcc compiler. S132 softdevice for nrf51822 controller.
And i am using s132 softdevice.
I want to connect multiple nrf51 devices (approx. 14...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I'm doing some measurement on the radio peripheral of the nRF52840 using the generated events and a timer which is set to run at 16MHz. Radio events and Start/Capture...
SDK version: 13.1
Hardware: nRF52832
Eclipse version: link text (I could not get the marketplace working in the latest Mars Eclipse version, so I downloaded this version...
I am evaluating the sdk14 ble_app_uart example. I am able to run this code and connect to this uart service but do not see messages get passed to the uart pin. Only when I...
I am using a nrf52832 Development Board with s132 for some BLE applications. I developed a beacon app, set for BLE peripheral, and every reading of the advertising from this...
Hi,
I'm using NRF51 DK board and i am following characteristic tutorial available. I am able to send temperature value over Bluetooth by using light blue app.. Instead of...
I am using nRF connect to debug an application on a nRF52832. When I perform a scan, I can see the UUID of the nRF52832 device I want to connect to. Where is this UUID stored...
Hi,
I'm unable to auto connect with nrf51 using nrf Connect App, if I select Connect using Auto-connect only and no Bonding in nrf Connect App for first time.
With Auto...
Hello,
i have a question about the range. I have a Bluetooth-Module with nRF52832. I tested it in my Office. Additional I can Change the Output power from +4 dBm to 0 dBm...
