Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I am planning to use an atmega32u4 as a micro controller for a keyboard, and I'd like to use a NRF51822 as the bluetooth sender.
As i've read, NRF51822 is BLE...
I would like to learn a little more about the process of negotiating a connection interval between an iOS and Android central and a nRF51 peripheral.
So, here are my questions...
Hello,
I purchased a nRF52DK to migrate my older projects running on nRF51822.
Version of the board is V.1.1.0 / 2016.19
I followed the 'Getting started' guide from...
Hello,
This is a DFU custom project...the core problem is that I cannot erase the bootloader settings page from the chip.
While trying to use a slightly modified version...
Hi
In current Desktop 2 project, We know that software device stack takes 48-bit random device address from FICR registers (DEVICEADDR[1: 0]) for BTLE. Each nRF51 has unigue...
Hello, I am devleoping a pc station using pc-ble-driver.
I was successfully able to install it on one of my computers but am facing a problem installing it on my surface...
The micro-ecc works well when I load micro_ecc_lib_nrf52.lib in keil5. However, the author suggest copying the uECC files into the project, so I include uEcc.h but fail in...
For the nRF51822, the documentation for ECB mentions it being used to
Encrypt/decrypt 16-byte data using
current key.
But it doesn't offer any methods to decrypt...
Hi,
Am using SDK 11.00 and NRF52 platform.
Am following below steps for dfu support.
1.Flashed Softdevice 2.00
2.Flashed dual bank ble Bootloader
3.Using nRFTool box...
Yan,
You mentioned these UART examples: examples\ble_peripheral\ble_app_uart or examples\ble_central\ble_app_uart_c I was not able to find them on your web site....
I have intention to use 52810's PWM output to drive motor. The timing requirement are critical so
hardware PWM is essential, rather than CPU generated waveform output.
...
Hi,
I am trying to increase MTU size for transfers and it works up to a size of about 72. After that I get an error.
Thanks to Sigurd I now know that it is when calling...
Hi, I've an application developed with SDK v8.0.0 and S110 v8, that is using the bootloader to start the main firmware and to start the DFU OTA (in case the user request to...
