Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I am using PWM for a buzzer. It is working, but the current consumption is always 300uA when PWM is not in use. This minimal current consumption appears right after...
1: my nrf51 SDK board not work , I replace the USB control IC--ATSAM3U1C-AU(the old is ATSAM3U2CA-AU),can you send me the firmwair of JLINK with this IC and the contacted...
Hi Nordic,
I want to know, how the button_push_sequence works on case of handling different events at different button_push sequence like... (--nrf51-ble-app-lbs--)
...
I'm using the pre-compiled nRF51-BLE-Driver-Win driver (v0.5.0) on win7 64b with python2.7 and an nrf51 dev kit dongle running the precompiled 115.2k s130 connectivity firmware...
BLE.c
when no connection creat between android nrfUart app and backon kit so autometically sleep in 180 seconds,
but i have need sleep condition in connected mode of...
This isn't a question, just a tip/head ups for people. Spent more than a few hours wondering why all my Flash settings all of a sudden were no longer saving. I found that...
Hi, the title says it all really. I'd love to get my hands on a sample application from the Nordic github repo (or elsewhere) which shows clearly how to implement for S110...
I've read the document, 51822 Product Specification 3.1
But I can't find which pins are assigned for SPIS.
I'm using QFN type.
Directly speaking, can I achieve SPIS...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
in our final device, I want to give the user the opportunity, to close an opened BLE connection between our device and another smart device. This should be done...
I have 2 boards. The first board, I run the demo project code for ESB PTX. And it works fine. However, I load the same code on a second board, and "nrf_esb_enable()" never...
I intend to use ESB to transmit data every a few hours. Since I want to use a beacon board, I assume the ESB app needs to sit on the S110 softdevice.
I added S110 to the...
Hello.
I use nRF51-DK and need to avoid appearing of the virtual drive during connection to PC (it's confusing my customers). So, I want a behavior as an old PCA10001:...
I am designing with the nRF51822 and I have a choice of either a 32Khz or 16MHz crystal. Can you tell me the advantages and disadvantages of both?
If the 32KHz crystal...
