Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hi,
By mistake, I clicked 'fill with zero' button in Jflash, may I ask, is my chip bricked because of this? Thanks.
The following lists my steps:
program the...
Hi,
I'm trying to use the SysTick timer on nRF52 to time some various tasks for debugging. I configured it like so, which I expected would cause SysTick_Handler to be called...
I didn't find any documentation in the peer manager for the need of this write buffers.
I do understand, that peer device data is stored there before written to flash. But...
Dear Nordic,
Device: nRF51422. Protocol: ANT+. Softdevice: S210 v5.0.0
I have 3 devices: two masters (No. 1 and 2) and one slave (No. 3). In my application, I pair the...
Hi guys
I have one nrf 51822 demo board.
And I want to buy one more board as BLE sniffer.
Can I use a nrf52832 demo board as sniffer to grab packet between phone...
Hi guys
I am programming nrf51822 demo board with sdk11 and try to finish service tutorials .
I finish all step in service tutorials and try to get service information...
Hi guys
I am using SPI example code in SDK11 (./nRF5_SDK_11.0.0_89a8197\examples\peripheral\spi) with nRF51 DK.
It works fine when send first data.
But it get in...
Hello ,I work with the sdk 12, I have a program to contoler the level of battery, it works, except that I recode 3870 mV (with USB) and when I measure the pin VDD I find 2...
Hello,
I am using an Android application to send data to a nRF52 board. The nRF52 board is the peripheral and the Android phone is the central. This is the link establishment...
Hi, I am trying test nRF52840-pdk throughput.
-I loaded softdevice s140_nrf52840_5.0.0-3.alpha_softdevice.hex into nRF52840-pdk using nRFgo
-Then I build (using uVision...
Hi, the datasheet for the nRF24L0+ says that the CRC is the mandatory error detection mechanism in the packet (page 28). Being that CRC can be enabled or disabled via EN_CRC...
Is there a problem logging into Nordic site ?
I have tried resetting my password and it doesn't seem to work. Had posted a question in the this thread earlier
Dear Nordic team and community,
Have you encountered the problem where standard BT4.0/4.1 GAP Peripheral device would be "blocked" from connection (kind of "denial of service...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...
