But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
According to the documentation, it is possible to upgrade the Thingy:52 firmware via a cable connection using nRFgo Studio. Can I connect the Thingy:52 directly to my PC?...
Dear Nordic Team,
Thanks for supporting.
Now i am trying to work DFU with NUS example.I am following As per nordic document like: infocenter.nordicsemi.com/index.jsp...
I am trying to communicate with DS1307 (RTC) using TWI on nRF51822.
I have configured the pins, address (0x68 fixed for DS1307), frequency and enabled TWI.
Now I am about...
Dear Nordic,
Some time ago we started a project in which we decided to use ANT protocol to communicate wirelessly. However, now that we are going to production in a very...
my programer have many place use sd_ble_gatts_hvx() send data , if i get the BLE_GATTS_EVT_HVC ,how i know this return value return belong which use sd_ble_gatts_hvx(),how...
how to save a problem,if one Thread use sd_ble_gatts_hvx() send many package ,but i use vTaskDelay(50)( the freertos delay api ) when one package send ,then send another package...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I read an article about the connection, pairing, bonding and whitelist, there are some doubts：
Bonding...
i want to send data according the ruture value , because we all the data send ruturn value ble_evt_tx_complete ,how i can distinguish difference channel'return value
I've been trying to trying to upgrade some code from SDK 12.1 to 12.3 and it no longer fits in 16k RAM.
I initially thought the problem was this data segment in the linker...
Hi,
I recently started working with the NRF51DK,I need to read data from KX022 accelerometer via I2C and transmit the results over BLE.
I am using TWI_SENSOR example...
when i send many package from programer different place , the return ble_evt_tx_complete have many times. how i distinguish which the ble_evt_tx_complete reture is that place...
I want to add DFU function to ble_app_beacon example,but I don't know what I should do?Who can give me any suggestion?Thanks.
My board is nRF52-DK.SDK is nRF5_SDK_11.0.0_89a8197...
Hello,
i have Nrf52840, here is the code for PWM
APP_PWM_INSTANCE(PWM1, 1);
uint8_t cBuzzer::_PWM_init(uint32_t Time_uS){
app_pwm_uninit(&PWM1);
app_pwm_config_t...
