Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
My setup is NRF52DK+SD132_V3.1.0+SDK_12.2.0.
While playing with my peripheral I setup a whitelist, the default whitelist filter policy seems to be BLE_GAP_ADV_FP_FILTER_CONNREQ...
Hello everyone,
I want to establish serial communication between 3 nRF52840 dongles using mesh.
Can you suggest me the steps from begining. Also i have read the documentation...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I enter break points inside ble_evt_handler, it always ends up at...
Hello,
I am trying to get Keil to work to program my Custom PCB. I am using Keil uVision5 MDK-Lite Edition
SDK: nRF5_SDK_12.3.0_d7731ad
Device: MDBT40-256R V3 (nRF51822_AC...
I need to incorporate eMMC in my code.But heard that it is not compatible in nrf52. So I would like to know how to include eMMC code right from the beginning the algorithm...
Hi,
I was able to run hid mouse example on my laptop. But when I tried to do the same on my other laptop it failed to execute properly, although the bluetooth pairing was...
HELLO SIR
we are working on our current project on bluetooth , we are trying to broadcast message via one nrf52 DK to other nrf52 DKs . i tried implementing the uart example...
Dear Sir,
I am trying to use a whitelist on peripheral side so as to connect the peripheral to a given phone/App.
At first I enabled the "p_advertising->adv_params.scan_req_notification...
I am requesting a USB booloader hex file or if possible the complete project. I have been doing some hacks on mine and have erased the USB booloader. A quick search through...
We are working on the BLE Smart Switch. The requirements are pretty generic:
Low Power consumption
To be used by multiple smartphones within the house
The obvious...
Hi,
I want to set the TX power in a mesh proxy configuration. I have read mesh sdk2.1.1 TX power of nrf52832 , which works good for not proxy situation (e.g for light_switch_client...
Hi, I'm having troubles adding PWM in light_switch_proxy_server example in Mesh SDK v. 2.1.1.
It seems that the PWM driver and instances are not correctly enabled, looking...
Hello,
I was wondering if there are any article or tutorial I can follow to optimize code build with Segger Embedded Studio.
I was able to follow this article( https...
I need logging in almost anything I do, but I've never been able to start from an example that does not use logging and add logging. I've set the NRF_LOG_ENABLED and NRF_LOG_BACKEND_SERIAL_USES_UART...
