I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
How can i add more nodes server in light switch example in Mesh SDK 1.0.0?, i change #define SERVER_COUNT to 52 and work fine, but when i change it to more than 52 don´t let...
Hi,
I'm using SDK 15.0.0 and NRF52840 DK.
I want to merge couple examples from SDK in one project. As "base" example ble_app_uart was choosed (..nRF5_SDK_15.0.0_a53641a...
I am using the code below to save data from an ADC into a circular buffer.
I then want to save that buffer for retrieval later so I do:
But when I look at the debug...
hi all
Every time the serial port provision the mesh with python, when the temporary variables disappear are defined when exiting the serial port , how to improve the code...
hi,
I am currently learning to use the mpu6050 read and write code in the SDK from the nrf5_sdk_12.3.0_d7731ad to control mpu9250. The part of the gyroscope and accelerometer...
Hello,
Is it possible to program nRF51822 with nRF52DK (PCA10056) ?
Currently I am trying to program my custom beacon (nRF51822) connected via SWD P20 header. I am using...
Hi
I succeeded to run the DFU OTA process and updated only the application. Application is running OK
The problem is that after repower the application is running but...
Hello,
I am trying to add NFC wake up functionality to the project based on ble_uart_app example;
Using SDK14.2 SD132 V5,1 using DK52 development board
I have added...
Hi,
I am trying to add interruption on light switch example. So, eu studied the gpiote example from SDK14.
When I add PPI, GPIOTE and TIMER libraries, on light switch...
So I have my custom board up and running (nrf51822) pluged into the nrf51DK with RTT debug comm and uart comm working, also starting some initial experimentation.
...
Hi,
I am using ble_app_uart service in my application. In my custom board GPIO pin 8 is used for LED. But this particular GPIO is configured for UART RTS pin in ble_app_uart...
When an NUS Central has several NUS Peripherals connected, is it possible to send the same "message" to all of the connected peripherals at once?
Or do I just have to iterate...
Hi,
It looks like we're experiencing an issue with uart's and digital inputs on an "S132 SoftDevice". Both an UART and digital inputs are used. The UART is initialized using...
Dear Sir/Madam,
I am playing with SDK12.2 on PCA10028 board and runs its HRS example. This example has a battery service and its battery level characteristic could update...
I use DFU. All ok. But I need to store my settings after update. As I was advised, I located my data from address 0x72400
But Keil added after this struc some code
...
