Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I’ve been working in a small group to use the advertising extensions in BT5 to send 12 hours of temperature measurements in one advertising packets. We’ve been developing...
Hello,
I am working on ble/audio application on nrf52832. I would like to know how to compile OPUS codec (used in smart remote) so I can use it on arm cortex. For now I...
Hello,
Would it be possible to use nrf_pwr_mgmt_run() to implement a polled wait function? The nrf_delay functions execute a busy wait which is only feasible for very short...
Dear sir,
I am trying to interface MAX 30205 with NRF52832. On thec oscilloscope I am getting the signals but still I am not getting the temperature data. Herewith I am...
Hi
We want to set +8dBm on DTM with nRF52840 but it test fail.
When I set +8dBm, nRFgo Studio cannot test it due to fail in DTM code.
We tried SDK v14~ v15 version but...
It seems like I should be able to find this in docs somewhere but having trouble finding the information.
What exactly is the sdh_stack_observer and if I'm ending up in...
Hi ,
I am trying to run one_wire example provided by this links
https://gist.github.com/pabigot/46502004045eeca86612
https://github.com/pabigot/bspacm
I tried running...
Does the count field in ble_gattc_evt_char_disc_rsp_t refer to the number of characteristics in that instance of the struct for the number of characteristics on the connected...
Hi,
I was looking at nrf52832 MCU reference design and found button connection as below
I would like to ask why R16 & R17 are used and how necessary are they? I understand...
I have Segger open with solution 'ble_app_thingee_s132_pca20020' and Project 'nrf52832_xxaa_s132'. I drop down Thingee drivers and left double click drv_humid_temp.c. An error...
Hello All,
I came up with one application .. where we are planing for industrial application , my requirement is as below,
there will be two nrf52810 chips one will...
hi,
i am doing a project where i am using a pca10040 board as central device and a another pca10040 board as peripheral device.
i am able to connect peripheral device...
Dear Sir,
My name is LH. I have bought nRF52DK for development. The marking on top of nRF52832 is "N52832 QFAA B0 1637CY". What is the IC revision notified with this code...
