Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi!
My setup:
* nRF52 DK
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* android ver.8 smartphone with nRF Connect
I have solved my previous...
We are using Nordic nRF24L01+ RF module. The RF library software is "nRF24L01P-EK" ( nRF24L01+ Evaluation kit files) obtained from the official Nordic website. RF module is...
Hi, I tried to implement ble uart service in an existing project but when ble is connected the original bsp buttons functions stopped working. After some debugging i found...
Hi,
I have some problems changing from the legacy driver to the new nrfx driver structure.
I have done the following:
1) Opened pwm example in SDK 15.0.
2) Renamed...
Hello Nordic team,
I am working on nRF52832 chip. My device goes in power_manage mode. Device wakeUp on pin interrupt but when pin interrupt occur device first reset and...
Hi,
I init the bsp for button, but there is no callback in handler when press on button.
The board is NRF52810, and there are so many problems when I test this borad....
Hi Everyone,
Pardon me if i write some illogical stuff. Complete beginner to this microcontroller.
I started using nrf52832 with Zephyr OS . I was trying to configure...
Hi,
I wished to test multiprotocol with one software but I was wondering if it was possible to compile an application which could switch between zigbee and Thread (and...
I'm using arm-none-eabi-gcc 7.2.1 with nRF5_SDK_15.0.0_a53641a with soft device s140_nrf52_6.0.0_softdevice.hex I'm trying to modify one of the bluetooth examples to add a...
Dear Sir,
I use nrf5_SDK_for_Mesh_v2.0.1_src.zip and test proxy server project,
I scanned the device nRF5x Mesh Light (0x1827 Service), I click "Discover services",...
Hi guys
I am trying to program a nrf51822 module but it is not recognized by the development kit.
These are the pins that I am using:
I can not see the...
Hi,
I am using nrf SDK version 12.2.0
The following code fails to produce event for twi transfer complete const nrf_drv_twi_config_t config = { .scl = I2C2_SCL_PIN,...
I'm using the P20 connectors in nRF52 PDK to flash my custom nRF52832 board.
The connections are like this:
SWDIO ----> SWDIO
SWDCLK ---->SWDCLK
VTG ------> VDD
...
Hello,
We have an application with a S132 device, SDK 14 and Softdevice v5.0.0. On some devices, an assert is being thrown in the sleep prepare function. This is the line...
