Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
How to write driver for ADC by accessing direct registers of nRF52840 ?
I don't wanna use SDK APIs.
I wanna read LDR value connected to A0 (PO.3) pin in continous mode...
Dear all,
I'm trying to change the advertised device name during advertising depending on some variables.
I'm observing with nRF Connect and Lightblue, both running on...
Hi,
I have followed the steps for the 2 demos for nRF52840 DK, the Heart Rate and the Proximity demo. In both cases, when disconnected from the android device, the evaluation...
Heey everyone,
I'm currently working on a wireless application and we would like to have a range of atleast 300 meter. Yesterday I was testing the range between 2 SDK...
I work with Kenkou GmbH in Berlin. We are looking for Firmware Developers and Engineers with Mid - Senior experience to support our project. We are hoping to extend the visibility...
Hi All, Nordic,
In my application, I don't always need BLE connectivity, so I was hoping to disable the S132 softdevice when not needed. However when I do this FreeRTOS...
Hi,
I am working on a project with BLE and TWI module. With some help, I manage to set a TWI communication ( https://devzone.nordicsemi.com/f/nordic-q-a/29371/twi-issue...
Every once in a while I will get a failure that results in the app_error_fault_hanlder() being called and the following info:
ID = 1
PC = 0x14550
error_code = 0x495...
Hi, I use ble sniffer 2.0 beta with nrf51 (pca_10031_51296aa.hex). Is there a sniffer api documentation with description of the UART protocol (as with sniffer 1.0.1)?
Good morning everyone,
I am facing a weird problem concerning the use of the UART service.
I am currently using the NRF52832DK to develop an application. In a nutshell...
Hi Forum,
I am working on nRF52840 THREAD sleepy node and facing an issue in deep sleep mode. The current consumption in deep sleep mode is more-around 60-70 micro Amp...
Hello guys!
Are there any difference in using FDS library with a nRF52832 or with nRF52810?
I will explain.
I'm using a FDS for writing/reading to flash for 2 months...
(I've seen several other posts mentioning similar issues, but many of them haven't resolved or found a solution that seems to apply in my case.)
I have a custom board that...
