Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I am trying to communicate with a MLX90615 temperature sensor via I2C and I am able to get the desired response from the sensor, verified with a logic analyser.
I am now...
Hi all,
I am working on nRF52-DK using the light client example under Mesh 2.1.1
I am trying to start and stop the listening for provisioning packets as the idea is to...
I've implemented a Battery Service and battery_level characteristic in my application (0x180F and 0x2A19 respectively) however, when reading the value of this characteristic...
Hi,
I am using one of peripheral examples ble_app_hids_keyboard from nordic SDK for understanding the re connection mechanism. I am using nrfConnect app. I have a few questions...
I am trying to use app_timer library with the provisioner example but I get this linker error.
The multiple definition error is due to nrf_nvic_state being present in...
Hi,
By taking a look at the source code in https://github.com/NordicSemiconductor/pc-nrfconnect-rssi.git, I found the following patch file under fw/src/usbd.patch. It mentions...
We use nRF52840-PDK (PCA10056) with MCU revision Q1AAAA. Given example of secured DFU bootloader (s140) works good. Then we changed MCU on this board to the MCU with Q1AAC0...
Hi to all,
i am working on a project that in it i want use nrf51822 as a peripheral device. i implemented a code but i have a problem, central(cc2540) and peripheral(nrf51822...
Hi,
I am trying to write 16bit, 16Khz, 2 channel PCM data to I2S. nRF52840 DK board is connected to speaker via I2S player/decoder board. I am able to hear audio but it...
How can I determine the correct value pull-up resistor to be used on the TWIM port?
The nRF52832 reference documentation mention an internal 13k pull-up however I've always...
I would like to create a program that was a mix of ble_app_multilink_central and peripheral_temperature. The program would work as follows: when the button1 of central is...
I am trying to migrate a blocking SPI transfer code to a non-blocking SPI Manager schedule call. I have 16 transfers queued up in one transaction.
When I launch it, the...
What is the best way to advertise a custom service and allow BLE connections from a mobile device in a Mesh SDK version 2.0.1 application. Previously I had an application...
Initially I had a project in Mesh 1.0. Everything (provisioning, send&receive) was working fine.
Since upgrade to the Mesh 2.1 there is an issue: provisioning still works...