Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
HW: nRF52, PCA10056
SW: SDK15
I'm using the nus_c service with multiple central connections.
After change the GATT Write operations from BLE_GATT_OP_WRITE_CMD to BLE_GATT_OP_WRITE_REQ...
Migrating from 13.1 to 15.0. getting error, undefined reference to 'ble_evt_handler'
In 15.0, peer_manager.c has the function, static void ble_evt_handler(ble_evt_t const...
Hello,
I tried a migration of a bootloader from SDK 14.2 to 15 but my bootloader does an infinite loop @0x24d70.
Do someone have an idea of what can i do please ?
...
I'm working on an application in which we are using a custom board with the NRF52382, which is powered by a battery. We sample our ADC every 6ms, record these values for about...
I try dual bank DFU on nrf52832+SDK15.0.0.
After extract new image to dst_addr(run image_copy),
DFU run nrf_dfu_settings_write().
nrf_dfu_settings_write() is run, nrf_dfu_flash_erase...
By setting either:
ble_gap_adv_params_t::duration
or
ble_gap_adv_params_t::max_adv_evts
to a non-zero value should trigger the BLE_GAP_EVT_ADV_SET_TERMINATED event...
We are planning to use Adafruit BLE Feather with the IAR / Keil/ SWD tool chain for a small scale project . I notice the Adafruit BLE feather memory map is quite different...
Maybe I'm wrong but this seems to be wrong ASSERT in the function:
My understanding is that max time which can be set on timer is dependent from timer frequency and timer...
Hi There, i am pretty new to this ble and arm world. i was exploring my nrf52dk with sdk15 cryptography libraries. I have looked into an example of Elliptic Curve Diffie-Hellman...
Hi,
I had done secure OTA in my custom board using SDK12.2.0 with S130 v2.0.1 softdevice. But when i am trying to update the same for multiple times then its not happened...
Hi!
I'm running UART example and modified to run upon interrupt and its working fine, but in main() if condition ( if (cr == 'q' || cr == 'Q') ) is not executing even condition...
Hi,
I'm trying to toggle GPIOs 32-35 but it can't be done. Other GPIOs though such as 15,21,30 I change successfully.
Here's my code:
I saw a solution regarding NFC...
Until lately, I have never used characteristics longer than the 20 Bytes and if the length of application data was longer, I would fragment it on the application layer.
...
