Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
I am working with production Rev 1 on nrf52840 DK v1.0.0 (2018.19). The spec section 6.35.10.2 Bulk and interrupt OUT transaction say
Until that transfer is finished,...
I am working on mesh application icatin nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for...
Hi all,
I am testing DFU example in Mesh SDK . I follow this tutorial : http://infocenter.nordicsemi.com/index.jsp . But when I execute to step 4 :
I get this error...
Hello,
I am new to Nordic products so please apologize me if I am asking a trivial question, but a bit lost on it. I would like to use Thingy 52 board for my project ( I...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
I want to add ANCS client to my code. Like in the ble_app_ancs_c example, I start a timer after BLE_GAP_EVT_CONNECTED. The timer handler calls pm_conn_secure() if the connection...
Hello
SDK12.3, nRF51822
I'm trying to interface the ssd1306 the program freezes in function app_twi_perform internal_transaction_cb is not called internal_transaction_in_progress...
With our nRF53832 device we are not using NFC.
For the lowest power usage should I keep them as disabled NFC pins or change them to GPIO pins and drive them to the same...
Hi!
I have a question regarding nRF51822 supply in internal LDO setup. Is decoupling capacitor on pin DEC2 necessary in this supply setup? Looking at schematic in nRF51...
Hi! As far as understood, there are only 2 clock cycles before the Watchdog timer reset occurs. Is there a way to change/set this to a different value? I need to write in...
Hello!
When using the NRF_LOG module along with a JLink, when I connect the probe to the nRF the RTTClient prints out the first lines that were written when the probe was...
i comple the ble_app_proximity in SDK15, Config APP_ADV_DURATION for 10s,after timeout, no BLE_ADV_EVT_IDLE occur in on_adv_evt.
how put the system into sleep mode?
