hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
Hello, I'm able get an updated battery service value on nrf connect using the 15.2 s112 proximity example on the DK using a cr2032. Then adjusted the clock to LF RC and removed...
Hi,
Let's say I have a door lock module without user interface... no keys nor display but with bluetooth peripheral module. The user pays is room via the application then...
Hello,
I would like to know if it's possible to simply configure all parameters for a BLE connection by a PC software.
The goal is to manage the BLE parameters to measure...
Hi,
I want to create 1 hex file that will contain my bootloader, app and softdevice.
I know i can use NRF GO studio in order to read each hex individualy but it is of...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
Hi,
we are testing nrf52840 together with rfx2411n amplifier to extend the range.
The problem is that we have same range and same RSI values when testing with bypass mode...
Good afternoon,
I have purchased multiple nRF52840 Dongles and so far have successfully ran blinky peripheral and master (required to adopt PCA10056) examples.
I tried...
Hello Nordic
I am testing SEGGER EMBEDDED STUDIO and I think it is little buggy.
When i simulate NRF52 application without actual device (I can not
debug on hardware...
Hi,
I used SDK_15.1.0, secure_bootloader/pca10040e_uart.
Through PC uart,it update successfully .But boot through android(linux) uart,it returned 'invalid crc'.Can anybody...
Hello,
I am working on BLE Peripheral and Central part on SDK11 for a long while. Now i want to start with NFC.
I tried to go through nfc section in SDK14 but could not...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
