Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I am using ble_app_uart service in my application. I am trying to send files using teraterm tool. If I am sending .txt or .doc files there is no disconnection in the...
Hi,
I am using nrf52832, and measure the power consumption , I found that when I use application timer "after" nrf_sdh_disable_request(), the power consumption of system...
Hello,
i am working on a nRF52840-Preview-DK with SDK 15.
When sending data out on UARTE1 with function nrfx_uarte_tx(..) everything works as expected but only with data...
Hi,
We are using nrf51822 QFAAH00 with SDK 110 v8.1.0 in our project, the application will hangs or not work when control stuck at address 0x6b0 (sometimes at 0x640) programmer...
Hi Nordic team
I would like to have golden version BLE DK as a BLE receiver.
Is the NRF52 compatible with other brand BLE DK or market product?
As I know the BLE device...
Hi All!
I moving from SDK 14 to SDK15 and faced with another errors:
after sd_ble_gap_scan_start(..) call, the BLE_GAP_EVT_ADV_REPORT message is occurred (once), then...
I used nRF5_SDK_14.1.0_1dda907.
I used fatfs example.
Wirted data in the same file to sd card.
I discoverd that Max size of the file is 16KB.
Over the max size of...
Are there any plans to include CMSIS-NN libraries in the SDK?
If so when?
If not, what build flags should I use to get the fastest runtime?
Thanks,
Quinn
how can I store outputs sent from JLINK SEGGER_RTT to a file?
how can I send data on RTT channel 1, is there any instruction for that?
/** loop */
sprintf (buffer,...
I'm trying to adapt the DFU bootloader to work with a SPI slave as the transfer mechanism, but I'm running into issues getting the SPI communication up and running. I've added...
I'm trying to load ble_app_hrs_c on the nrf51dk and im getting the error
"error: L6047U: The size of this image (34328 bytes) exceeds the maximum allowed for this version...
Hi,
I am trying to receive BLE advertisements on Ch38 (=2426MHz) without using SoftDevice, i.e. with direct register access. However "EVENTS_DISABLED" is very rarely called...
Nrf52832 based on sdk14.2 development as a slave, when linked with the iPhone, pairing and binding, and then get ancs service; and Android phone connection, direct communication...
