Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello,
We are porting legacy application to the nrf52840. We are using Keil uVision 5.
The legacy code is using some gcc ideas and extensions so we are forced to use...
Hi ， All
I am using nrf52832 SDK12.3.
When the host runs to the discovery service but has not yet discovered the service，the slave power off. The host can no longer connect...
Hi there.
I Tested Example (secure_dfu_ble_s132_pca10040). Fine work.
but I could not find the example code to transfer the firmware.
I need the code to receive...
Hello,
I'm a little bit confused about max datalength that can be read/written in a characteristic.
See attached, a MTU of 64 bytes is negotiated thus 61 bytes available...
hello there! I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller nRF51822 for connection and data exchange...
I uploaded a sample code into an external nrf51822 module using nrf51-dk as explained by this blog www.instructables.com/.../ . power supply for the external module was from...
Hi
The following ticket explains when I configure pin21 as RESET it will be hardware configured to pull-up internally. https://devzone.nordicsemi.com/f/nordic-q-a/8342/nrf52832...
Hi all,s
I have a couple of nrf52840 boards and i was testing the ble mesh light application. The application works fine, but i changed it so it will periodically set...
Hi, I have tested thingy52-mesh-provisioning-demo in NordicPlaygound on github. It works fine by using a precompiled hex file (via nRFgo Studio) but It doesn't work (light...
Hi, I'm working on enumerating the 52840PDK as a CDC ACM device and I'm running into an issue where it's fully enumerating 80% of the time.
After doing some checking I've...
I'm working with TI's TAS2555 DAC as an audio output driven by the NRF52 via I2S. This DAC requires that the I2S clocks (MCK, SCK, and LRCK) are enabled prior to any data...
I understand that the next version of the mesh SDK will have the GATT proxy implemented. Even after reading the mesh profile specification the following is unclear:
- Is...
Hi,
our product is small tag, size of 70x35mm2.
Plastic covers are welded together and now looks like after welding some HW does not work properly. Flashing is successful...
Hello, I am running ble_app_uart_c example on nrf52832 IC. It is connecting to its corresponding peripheral and I achieved bidirectional communication.
The problem is,...
Hi! I am using SDK15 to develop an application for nordic chip which won't be using any kind of display nor keyboard input, so probably I'm gonna go for static passkey option...
