Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
Hello,
So I'm loooking for a way to transfer relatively small quantity of data live as reliable as possible and as quick as possible between two nrf5 units and then between...
Hi,
I am using Nrf51422 DK, my need is to send file (which is placed in my computer)to the another nrf board. Tried with file operations (fopen,fgetc,etc.) in keil4. It...
While flashing program to nrf51822 device through terminal getting these error msg
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists,...
Hello, I currently using the proxy light switch exemple of the mesh SDK 2.0.1 in this configuration :
I search to have the less current consumption in the mesh client ....
Hi all,
Please find my following current measurement resuls in the pwr_mgmt example using a nRF52 preview DK and SDK 13
My setup is as follow:
SB40 is cut
SW6 is...
int main(void) { initialize(); execution_start(start);
for (;;) { (void)sd_app_evt_wait(); } }
can you explain me the execution of code flow in the main with these APIs...
Hi to all,
I am new i ble tech, i read some where that notification charactristic dose not need acknowledgement but indication need, now i want know that this acknowledgement...
Dear all developers：
I want to use whitelist on central mode，and using SDK12.3.0. I have see some call be used like this:
pm_whitelist_set（whitelist_load()）
p m_device_identities_list_set...
Hi,
We are working with SDK 15 with the HRS freeRTOS example. we did some modification to the advertising modes so that we advertise on fast mode for 1 minute and after...
Hi,
I'm using nRf52832 with SoftDevice S132 V3.0.
I found that I can exclude a bluetooth channel from the map by function sd_ble_opt_set .
But how can I tell that a...
When I compile the project (nrf5_SDK_for_Mesh_V2.0.1) exemple: Light_Switch....... there is an error that appears
#include "boards.h" --> (no such file or directory) Why...
I'm using SDK mesh v1.0.1 and nrf51822 S130 for mesh application. Light switch example is working fine. Now I want to add a twi sensor in server side. My doubt is in mesh...
Hello,
First, the current of the advertising frame was too high (around factor 2) and I have switched on the DC-DC to correct for that by inserting sd_power_dcdc_mode_set...
