Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
Hi, Everyone
I am developing based on ble_app_uart at nrf52832 (softdevice s132)
I modified the program slightly.
- After the connection is confirmed
- Send 100 bytes...
Hi Devzone:
I have build up a environment that are
1. a thingy52 with mesh-briadge
2. a thingy52 with mesh-node, which is control by segger-debugger, and it shows
...
Hi everyone,
On my actual configuration I can connect one smartwatch to the nRF51422, and re-connect it later if the communication have been interrupt.
However when I...
Hi Everyone,
I've looked around at the Nordic documentation before asking this question but can't find any good example. I am looking for an example to create a repetitive...
hi
I need to set a pin high when i make a connection to the device .so i set to output direction in main.c file.i have include gpio.h and nrf_delay.h file in main file ...
I'm using the nRF52382 with SDK 14.0 and softdevice s132 5.0.0, and I need to send up to hundreds or thousands of kilobytes to an Android phone over BLE. I need to optimize...
I have a custom beacon with:
nRF5_SDK_12.3.0_d7731ad
I am using:
\examples\ble_peripheral\ble_app_beacon
With:
\pca10040\s132
When I change the value:
int8_t tx_power...
In my project, I want to store data in the form of hex or bin file in the flash memory and send it via spi to the slave device. Can anyone suggest any example on how to start...
As far as I know NRF52840 SoC has multiprotocol radio: "The new radio supports multiple protocols including all the new features of Bluetooth 5 plus 802.15.4-based protocols...
Hi,
we are working on beacon project, we are facing current consumption problem.
When we dump the code in nRF52DK we are getting around 20(uA) current consumption.
When...
As per recommendations with SDK15 I'm using the nrfx drivers for peripherals. When I attempt to compile, the linker fails as it cannot find the function nrfx_saadc_sample_convert...
Hi there!!!
The NFC pairing demo from Nordic was fascinating!
According to the Bluetooth SIG blog :
Provisioning Bearer A provisioning bearer layer enables the transportation...
Hi! We've got a nRF51 based device where the firmware was developed on SDK version 8 (reportedly based on its hrs_c example) with S110 softdevice. We are now developing a...
