Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I have made a custom board by following the reference design given in the nordic website using 2450BM14E0003 Balun and 2450AT18B100E chip antenna from Johannson technology...
HI,
My application is based on on your example ble_perepherical/ble_app_uart.
I realised few modification.
Now, after a BLE timeout, the circuit doesn't sleep anymore...
I am requesting timeslots with an interval of multiple seconds. But sometimes I want to switch to an interval of several milliseconds. How can I cancel the pending timeslot...
Using some of our nRF51 dongles as sniffers to debug BLE.
Sniffer software --> "w" --> Wireshark, no problems.
Post processing wireshark export *.csv files. No problems...
Hi.
Is there some code example for Bluetooth button for PTT aplication Zello ?
When I press a button BLE should send notify event =1, when released BLE send notify event...
I'm building battery power BLE mesh network the nodes mast have the publishing period match greater than 5 minutes. And my question is how to estimate the power consumption...
Hi, I have a spis problem when nrf_drv_spis_buffers_set is called, it enters the switch on the SPIS_BUFFER_RESOURCE_CONFIGURED case, then calls spis_state_change with SPIS_BUFFER_RESOURCE_REQUESTED...
Hello,
I'm using the examples light_switch_server_nrf52832 and light_switch_client_nrf52832 to send data over Bluetooth Mesh. Using the description from creating new models...
In the SDK the multi protocol example switches back and forth between Gazell and BT with a button press. Is it possible to maintain a BT connection and a Gazell connection...
Hi,
I have a quick question regarding isochronous data transfer. This type of transfer is still in the draft but are there any hooks in SoftDevice that would enable us to...
Hi I'm brand new to use nrf52840, but hope there is one that can help i need a counter / timestamp. If it's a counter, it still has to count even if you do something else...
Hello Everyone,
I am using Martinsbl / nrf5-mpu-examples nrf52-mpu-easydma-using-timers-and-drivers. When I tried to change the TWIM_RX_BUF_WIDTH to get the gyro data, the...
I'm totally new to Nordic solutions. I was programming a lot in assembler in 8051 era 20 years ago. Now I feel lost in that new solutions.
I have PCA10040. It is connected...
Hi everybody
I'm working on an application where I want to sample microphone data with the adc (NRF52 DK board, nRF52832) and send it over BLE to a central device. I've...
