Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi all,
I’m Bruce — first-time poster but have been working with the nRF9160 on and off for a while now, mainly in outdoor, power-constrained telemetry and monitoring applications...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
I am using example code TWI_sensor. It is the same code i just switch ports and added couple of lines that would power up my sensor. After running it i can't even clk going...
Dear Community;
I am using this code provided by a Nordic engineer to make some HTTP request in order to use Telegram Bot API . It works fine but after 1-2 days working...
Hi,
I am in search of an SoC capable of processing data and having Bluetooth features. I have to use it in an automotive design and need to be compatible for the application...
Hi, I am having an issues when i run the command
west init -m https://github.com/NordicPlayground/fw-nrfconnect-nrf This is the response : I found a similar issue here but...
I'm trying to find documentation about the RADIO peripheral of the NRF51822 chip. In the NRF SDK file nrf51.h i can find all the registers like 'PCNF0' and 'CRCCNF' but there...
Trying to setup nRF Sniffer v2.1 for nRF52 Development Kit (PCA10040)
1) Wireshark does not see the Sniffer. When I run nrf_sniffer.bat, I get this:
C:\Program Files\Wireshark...
Hi,
I am now trying to reduce the total number of packets during the dfu process. After reading all the code about dfu in both app and bootloader, I find that in this process...
I am trying to install the pc-ble-driver onto my PC so that I can get the dll and lib files necessary to read/write from a nRF52840 Dongle programmatically. I am following...
Hello, we are using microchip bluetooth as uart tranpsarent and we have custom app in android to control it. In future we are going to do mesh application in android. But...
Hi
Using SDK for Mesh 4.0.0
I had a strange behaviour: Setting up a model with publication period 16s resulted to an interval of actually 10s. Multiples of 10s were working...
Two traces are attached performing the same function. A connection is made to a bonded device. The peripheral times out and the central tries to reconnect. with SDK 14/SD5...
