Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
The 9161 has 256 KB of RAM, but while building the application, it reports that only 32 KB is available for the application. If I create some large static buffers (e.g. 10...
Hi Nordic Team,
Setup:
Board: nrf54l15dk
NCS: v3.0.1
I use LOG_INF and printk to print data in minicom or Serial Terminal v1.4.3 from Nordic. Printings seem misformatted...
Hi,
I am porting a SDK 2.6.0 project to SDK 2.9.0. It gets built without errors but when I try to run it after flashing I get the following.
I am not sure where to start...
I am working on an nRF52-based BLE peripheral (beacon) using the Nordic SDK. I want to implement functionality where the advertising interval can be updated dynamically from...
I've developed a custom Matter application based on the Matter samples in the Nordic Connect SDK, targeting the nrf52840. I developed the first version using the nrf52840dk...
Hello,
I'm trying to connect a BMI270 sensor over I2C using Port2 on the nRF54L15 , with the nRF54L15 DK , and I'm working with the nRF Connect SDK v2.9.0 , based on a Zephyr...
Hello,
I am using Segger Embedded Studio to run AWS FreeRTOS bootloader demo on the nRF52840. When I try to build, I get the error cc310_bl_backend_ecc.h: No such file or...
the first (initialized) Eddystone (e)TLM frame have vbatt unset. I am using SDK 15.3. I suggest the following changes, it simply busy wait until ADC reading is finished before...
I had been programming custom boards with the nRF52840 DK both through nRF Connect and the Command Line tool without issues. I have shorted SB47 to provide power to the target...
Hello,
I am see odd behavior with SES and git repos. I was working on a branch and wanted to confirm there was no issues with the building the project before I started adding...
I am sorry to ask a stupid question as i supposed to fix firmware issue with my zero knowledge.
Before android app (central) connected to peripheral ble 52832, If I press...
Hello,
We have developed a GATT based application based on nRF5_SDK_15.0 (Bluetooth LE without mesh). We want to add mesh functionality in this code as you described in...
Hi, I am new to Nordic devices. I have purchased Nordic Thingy91 (PCA20035).
I need a small clarification on the programming/flashing the nRF9160 and nRF52840 on Thnigy91...
Hello
I am trying to operate the ble_peripheral_hrs example found at SDK 5.11 (several years ago) for Segger, but I can't found a project (*.emproj) for it.
Have you know...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...
