I have a project that I need to use most of the GPIO pins available on the nRF52840 DK. I'm using SDK V17.
I'm writing a test program that toggles all GPIO pins on an nRF52840...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Simple question:
Is possible a central to evaluate RSSI before connecting to a peripheral?
The idea is to make central device connect and bond to a peripheral only if...
I'm writing some DVT tests what I'd like to see the output from the test display in real time on a RTT log. By real time I mean that if a log statement prints something, I...
I've been running into an issue when running examples from SDK 15.2 (S132 6.1.0) on a custom board that uses a Fanstel BC832 (uses 52832 soc) module.
At the moment I have...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0, using gcc. I only just got it to link and flash. I'm using the RTT logging and the flashlog. The RTT logging is working...
I have just received a set of nRF52840 dongles and I want to write applications that run on the PC using the dongle so I have downlaoded the pre-compiled pc-ble-driver located...
Hello, I am using SDK version 15.3 and nRF5280DK.
I am having trouble finding an example that uses the button handling library .
From the information I could find on the...
I've been trying to connect my device to AWS IoT for a week, but I'm getting the same error "no matter what" I do (ERROR: mqtt_connect -45), which seemingly is an authorization...
Hi! We're developing on an nrf52840dk and have been running in to some problems when we want the system to only pull currents in the size of a few microamps. As our system...
hi, i'd like to make communicate 2 different nrf24l01+ without the enhanced shockburst if possible, i'm using arduino to control the tx and fpga to control the rx; i'd like...
Hello!
I am trying to improve the GPS-performance of our custom board. It is difficult to know if it is my hardware, firmware, antenna or something else that needs to be...
Hello, im relatively new to this and not sure why im getting this error. According to previous such error clarifications, i read that the newest versions have to be used....
Hi I have a couple of Thingy:91 devices, which we are using to evaluate the 9601 SoM.
The devices ran out of credit, but after buying more iBasis credit still would not...
Good afternoon. I use NRF 51822, and I want to use RTC 0 or RTC 1. But there are problems, if I do not initialize BLE then the compiler does not execute LFCLK_config because...
We are now developing BLE ADC sender, using nRF5_SDK_14.0.0_3bcc1f7, and two nRF528322s (sender and reciever).
We send SAADC data via BLE, after that, we disconnect, and...
