Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I've finally worked around some funky bugs that only appeared after updating to 15.3. In my app, I had to change my clock source to RC or SYNTH to make it work (was hanging...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Ok so I am trying to integrate SPI master and slave initialization code. I am very confused about legacy and non-legacy drivers and HAL. I am getting strange compilation and...
Hi,
i am working with nRF52832, i need to us sleep.it may be do somthing and sleep 40ms,rtc wake up it and do somthing and cycle.
i see the rtc example but it may be some...
SDK: 15.3.0 Example: ble_app_multirole_lesc Device: EYSHJNZWZ (nRF52832)
I called "pm_init" to do "PeerManager". Then, a part of FLASH has been written to "DE C0 AD DE FE...
HI,
I compiled MQTT sample, and always got :
ERROR: mqtt_connect -60
timeout error.
It seems that it takes about 2 minutes to get LTE link connected:
LTE Link Connected...
https://github.com/takafuminaka/nRF52832/blob/master/i2s_ws2812b_demostration_planB/i2s_ws2812b_drive/i2s_ws2812b_drive.c
I read the documentation, but didn't really grasp...
I'm attempting to use the UDP with PSM sample provided at this Nordic nrf9160 samples branch . I haven't changed anything within the sample itself. I've been using it to demonstrate...
Installed Segger Studio v4.12, nRF5 SDK(latest version), J-link, all under same catalog but into their own respective catalogs.
First, if I open blinky catalog and choose...
I am receiving "ERROR 4097 [Unknown error code]" returned upon calling nrf_sdh_enable_request. I found that ERROR 4097 corresponds to NRF_ERROR_SVC_HANDLER_MISSING from some...
I have the following code. I need to add a second counter attached to the spi_end_event. The first counter "count_task" is working, but can you tell me how to get "count_task2...
Hello all,
we have currently a problem with writing to a custom chracteristics in nRF52832 with softdevice S132. When the characteristic is written, we get responses only...
Hello, i am making a "simple" project, the goal being changing the duty cycle of the pwm depending on saadc sample value. My goal is to sample audio, process it ( low pass...
Hi,
I am implementing a keyboard with nrf52832 + s132 from sdk 15.3.0. Recently noticed that when trying to pair the device with a Windows 10 laptop and it keeps saying...
