hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hello!
Our current project is bare metal and has logging over CLI. I'm in the process of setting up a new project of ours that uses FreeRTOS but reuses a lot of the same...
Hi,
Greetings!
We are about to select nrf52832 for our product development and we need confirm below information before proceeding further
Overview
Device will be...
Hello Nordic.
I find two RNG example.
Both nrf_crypto_rng_vector_generate and nrf_drv_rng_rand , what is the difference?
Which one is better on RNG.
How to correspond...
I am trying to set up developing environment, and however I couldn't download and install version 7-2018-q2-update of the GNU ARM Embedded toolchain.
Would you please guide...
In my application i need to use NBIOT network & GNSS.
For that i found that i need to configure AT%XSYSTEMMODE=0,1,1,2.
But i am not clear on what should be configuration...
Central info SDK: 15.3 nRF52840
Uart communication is used. In rare cases, the value obtained by checking the waveform with an oscilloscope was different from the value...
Hello everbody,
I readed alot about the nrf52480 "how to flash softdevice and the other stuff", but i cannot get the ble_app_gls working out of the scratch.
I have the...
Hello everyone, I am trying to implement audio processings algorithms with my nrf52DK.
What i need to do in order : 1- Sample my audio signal ( It will be guitar sound ...
I need to use a nRF52 chip to handle interrupts with low (and known) latency. Basically, there are specific ~100 us long intervals during which I need interrupt latency to...
I am trying to setup a VM (Ubuntu 19.04) that has the complete setup for NRF91 development. I have been following the instructions in the nrfConnect 3.2.0 - getting Started...
Hello Devs,
I am using app_timer to create multiple timers to read different sensors
Currently, I have 5 timers created using app_timer_create, each timer has their own...
I use nRF Connect for Desktop to download hex file(nrf52810).
Use the following example：
nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble + nRF5_SDK_15...
Hi,
How do i turn off the nrf power management library? Is there any function like nrf_pwr_mgmt_uninit()?
The reason i want to turn it off is because it causes the usbd_msc...
I have a requirement for BLE and 802.15.4 stacks in a multiprotocol environment. I have looked at the sample at NordicSemiconductor/nRF-IEEE-802.15.4-radio-driver on github...
I am trying to initialize the RTC and trigger an interrupt every 10 seconds, and I am unsure of why the code above is not working. I followed a similar method to initialize...
