Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi
We will use the 52811 together with nRF9160 for short range communications. Currentconsumptionwise which interface is recommended, UARTR, TWI or SPI?
I am trying to run the example secure_bootloader\pca10040_ble_debug. The application does crash during a debug print with following stack trace:
Any idea what could...
I've reached a critical point in the firmware development process where I need to start considering integrating a bootloader with the application code.
I have a custom board...
Hi,
I'm trying to update the modem firmware on my nRF9160. I believe the current firmware is mfw-m1_nrf9160_0.6.8-30.alpha. I followed Martin's suggestions here , but nRF...
Hi,
If i had a purpose of including Ble files into peripheral example then what is the way i can approach?Is it by including all neccessary header file paths,adding sources...
I am working with nRF52832 platform and using some Bluetooth examples like blood pleaser and heart rate. I am wondering how I can count the number of data transferred bytes...
Hi, I try to combine example Blinky with Uart. but i have problem error as link below
Output/blinky_pca10056 Release/Obj/main.o: in function `uart_init':
undefined reference...
Hello,
I am a new user.
I am currently trying to use the 1NCE and Hologram sims, and using LTE Monitor to check the connection.
I am able to see that the signals are...
In our application we use nRF24AP2-USB for some time now.
To test the ANT antenna we use a test program called "USB2_IQC_Test.exe".
This program compares a DUT with two...
I currently have a piece of firmware that uses SDK 15.3.0. The application that have developed that makes extensive use of PPI channel 1 to drive ADC sampling with a timer...
Hello, I'm just starting to experiment bluetooth with the nfr52840 DK board and the sample programs available, especially those "ble peripheral" and as a beginner I started...
Hello,
1) I am using the PCA10040 to program a nrf52811 chip on a custom board with SDK 15.3.0.
2) I'm using the example ble_app_uart_pca10040_s112 on uKeilV5
3) Initially...
Hi I wonder if there are any PPS signal from gps part to the cpu, preferable some kind of timer input or interupt port so it is possible ta make absolute timestamps with fractions...
Hi,
We are using nrf51422 in our project.So right now i am loading the program using the Usb cable .Here my doubt is can we able to flash the program by using usb to uart...
