I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi to everyone!
I have a problem when I try to connect to the Blinky application running on my nRF52dk.
My mobile phone (Nexus 5X, Android 7.1.2) is able to detect the...
Hello,
I am learning the different peripherals using the nRF52 DK (PCA10040). I am using the nRF5_SDK_16.0.0. I am using Segger Embedded Studio on Windows 10 64-bit machine...
Hi,
I am trying to use enhanced shockburst (ESB) to stream data at high bitrate between two nRF52 development boards. Even though I set the protocol to 2Mbs, the max netto...
I am testing a nRF9160DK board. I am located in Italy, so LTE-M SIMs would not work.
I have received some NB-IOT SIMs from TIM/Olivetti; I found a compiled sample "at_client...
Hi
I building a mesh network of sensors that will be spread across a building.
One node will have a cellular modem and will send the data to the cloud ( gateway ).
Data...
Hi, I got maybe strange and difficult question about nRF24E1 - I know that max supply is 3.6V, but I try to rebuild one project to Li-ION and I would like to ask if that chip...
There are many one star reviews for nRF Toolbox on the Android Play Store (not from me!). These one star reviews are from users complaining that the application does not find...
Dear All,
I want to program a device to perform the following actions:
Start->configure modem to connect to NB IOT, adjust the PSM and EDRX->potentially send a message...
Howdy,
Part of our design process for trying to achieve the most time out of the product's battery is optimizing any pull-up and pull-down values such that when active...
Hello,
After adding pairing using static passkey to my nRF52840 board, i am facing a memory issue :
At the beginning of execution, the code stopped as if there was a breakpoint...
Hi
I have a short question:
I am currently writing on my master thesis about an self built Asset Tracking System. There should be a micro controller as a receiver...
Hello,
I am using Segger Embedded Studio to run AWS FreeRTOS bootloader demo on the nRF52840. When I try to build, I get the error cc310_bl_backend_ecc.h: No such file or...
the first (initialized) Eddystone (e)TLM frame have vbatt unset. I am using SDK 15.3. I suggest the following changes, it simply busy wait until ADC reading is finished before...
I had been programming custom boards with the nRF52840 DK both through nRF Connect and the Command Line tool without issues. I have shorted SB47 to provide power to the target...
