Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi All
We have an application using FDS, the SDK is: nRF5_SDK_15.3.0_59ac345 and the soft device is: s140_nrf52_6.1.1
There are 32 x 1024 byte FDS pages.
When the FDS...
I have SAADC configured in burst mode with 4x oversampling and tACQ=5uSec.
What is the total conversion period?
tACQ + tCONV*4 or (tACQ+tCONV)*4
In other words, is Sample...
Hello
Good day!
For example, if I have to use a Capacitive wheel sensor of 3 touchpads with the Csense example on SDK 16, do I have to configure 3 different output pins...
Hello,
I have an application to develop in which Central device is scanning with use of whitelist if it is not connected but have saved peers. If peer list is empty, device...
I have trouble when discover the BLE Peripheral that have the base UUID of characteristics and service are different. Then I followed several instructions in some cases, but...
I am trying to run the SDK15.3.0 gfx example code - only changing line 82 to:
And also I have changed the sdk_config to the display's width and height. I have wired it...
hi
I want to update RTC time in my device nrf52840 through nrf connect app. How can i do this? Is there any related example which may help me in doing this?
Hi,
I'm attempting to use OpenOCD to perform the equivalent to "nrfjprog --recover", since we've recently started using that feature.
I read through this case, but it...
Version 4.20a (Win x64) of Segger's Embedded Studio has problems with it's C syntax highlighting -- specifically conditional compiled sections of code. Code that is not being...
Hi,
We are using nrf52840 to develop a cryptocurrency hardware wallet. We want that user can verify that the device is authenticate. In order to authenticate, the desktop...
Hi,
I'm using Kail and I have a project with original target device nrf52832xxAA, I need to change it to nrf52832xxAB (the device onboard is nRf52832QFAB).
When I...
Hello,
I have to send SMS from NORDIC nrf9160dk which is using iBASIS sim card to my mobile phone. For this I tried two programs (at_client and simple_at). But nothing works...
Hello,
I am trying to run https://github.com/sigurdnev/fw-nrfconnect-nrf/tree/master/samples/nrf9160/i2c_scanner exampl. It is not compiling with the zephyr right now...
Hi,
for a new project we use the NRF52480, I can get it into low power mode with a total use of 20µA ( with all the other hardware on the board ). But when I initialize...
