Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi
The slave select (ss) pin during the spi communication is always low even when i make it high to release the spi bus. It looks to me that I'm not actually controlling...
Hi All,
I got 66uA current consumption in sleep mode and trying to reduce it further to few uA. I have disabled the serial interface and still wondering if there is anyother...
Hello All,
I am working on the nrf52810 module.
I am using sdk 15.3 with softdevice 6.1.1. (IDE segger)
Issue-
1. I am giving the Advertising name as " TEST_01 ...
Hi everyone,
this is my first question in this blog.
I am trying to use the library pc-ble-driver-py in order to interact with a DevKit (in which an example code is implemented...
Hello!
I want to use a long range and buttonless bootloader in nrf52811. S140 cannot be used for this task, because S140 use more then 150KB of flash.
Is it planned to...
I need to download nRF Sniffer v2.x, but the link is not valid, please send me a valid link
Old unavailable address: https://www.nordicsemi.com/Software-and-Tools/Development...
Hello,
I have to send hardcoded AT commands on button press on nRF9160dk. So for that, first I did program for button press. It is working fine. Then I did simple_at program...
Hi,
SDK: nRF5_SDK_00.11.00 ; S132 SoftDevice v2.0.0
I am working now to migrate my application from DM to PM (in order to better handle pairing&bonding).
Sometimes the...
Hi team, there is nRF52840 connected to STM32 via UART, the goal is to receive STM32 firmware over BLE (using nRF52840) and send the firmware to STM32 via UART.
My goal...
Hi!
I am realizing a comunication between a serial device and the nRF52832 through UART; i set PIN 5 for TX and PIN 10 for RX (after set PIN 10 for GPIO use) and i don...
Hi
I am planning to use Zephyr Rtos on a Telit Module (BlueMod-S42) based on the nRf52832 SOC.
As we are making both Client and Server application, the question has 2...
I was using a sample code from here which was posted by Jørgen Holmefjord at the link: https://devzone.nordicsemi.com/f/nordic-q-a/43750/to-display-uuid-major-minor-values...
Hi,
I have got the new nRF9160 DK (pca10090) and I have connected. But it's continuously rebooting, without any changes.
And not able to add the device to nRF could account...
