Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi
In the mqtt_simple example there is a line " modem_configure(); " which establishes the LTE Link connection. If connecting the LTE link is not possible (for example no...
I have now removed all my experimental code and have returned to the more or less original verion of the main.c for assec_tracker, but still the application seems to be stuck...
We are using the Nordic nRF52840 on our current design. Currently, I am using nRF Toolbox -UART app on my
mobile phone to send data via 9 buttons available on the App. Everything...
I am trying to read the data of an MQ-6 sensor, which is its gas sensor, but the data I receive is not from the reading by the values it shows, if you know how to do it or...
Hi,
When the bootloader address resolves to something invalid, fds_init will hardfault. I think it should have some check and return a nice error code instead.
See an...
Hi,
I want to disable all four buttons to my rigado bmd 300 evaluation kit (pca10040 is the board config. the same as nrf52 DK ) in project ble_app_uart
I have tried to...
I'm powering an nrf52810 with a 3.3V regulator. I understand the internal LDO powers the system at 1.3 V. Are the GPIO pins and other peripheral devices outputting 3.3V for...
Hi
When I select the Generic Level server model and try to bind the app key I get an invalid model Error. I am using the nRF Mesh android app.
This might be relevant or...
Dear Nordic Support,
I am using ble_nus service on nRF52840 (BMD-340-A-R) + Raspberry Pi 3B+ ( https://github.com/IanHarvey/bluepy ). The nRF52840 is the peripheral and...
Hi,
I would like to know the I2C bus capacitance for the nrf52840. Do someone have the information please ?
My slave components are compliant for 400Khz and VDD is 3.3V...
I have gone through the tutorial on mesh experimental dimming and I was able to provision the BLE nodes, contol and dim the LED1 on the evaluation module with RTT viewer....
Hello everyone,
We are having a problem with the DFU function in our custom iOS app.
We are using DFU library version 4.5.1.
After updating SoftDevice and Bootloader...
I'm using the nRF52840 DK to develop my application using FreeRTOS while trying to achieve the lowest possible consumption. I'm having some issues so I went back to the ble_app_hrs_freertos_pca10056_s140...
hi
i use the example flashwriting in nRF5_SDK_15.3.0_59ac345, i set a table at 0xfd000:
// ProgramSection alignment="4" keep="Yes" load="yes" name=".tabletest" address_symbol...
