Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi All,
I just start to use the Thingy 52 and I would like to know if there is any source code for development purpose for Windows. Also, which development software does...
in SDK/examples/peripheral/blinky/ hex
there is one file
blinky_pca10056 _mbr .hex
in
SDK/examples/peripheral/blinky/pca10056/ mbr /ses/Output/Release/Exe
there...
Hi
I am very new to BLE...
We are looking into a new industrial product design that will be battery powered, and be capable of communicating with BLE sensors (Mesh not...
Hi!
My software setup consists of SDK 15.0.0 and SD 6.0.0.
I am using nRF52DK for flashing and debugging my custom PCB board on nRF52832.
I am developing an application...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
1) At factory first we will load Secure Serial Bootloader and SoftDevice...
We are building a prototype for a wireless solution using nRF52840 and we found that the UART included in this MCU does not support Odd parity. This is a major handicap that...
Hello, I am writing a Program where I use GPS and NBIoT. Recently, I wanted to combine the default GPS example code with an NBIoT Code, that connects to a TCP Server and when...
Hi,
We are using Eclipse editor for nRF52833 SDK 16.0. While searching GDB support for nordic devices i found following link
https://devzone.nordicsemi.com/nordic/nordic...
Hello,
I am using the nrf9160 and I am developing using zephyr. I have an nrf connect project in Segger IDE.
Generally I am able to edit and build my project. The problem...
dear :
i used sdk 12.3 development bt mouse. now i have a question.
when one mouse link pc , its mouse x/y axis is ok.
but if two mouse( same code) link pc. oen mouse...
Hi all,
I used nrf cloud gateway servie last week. It's work very well.
But today i get some problems
1. i can't delete device. If i delete device, then it will go to...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
I am new to DTM. I have related queries.
1) In nAN34 note, what...
Hello, I have been trying to get the asset tracker demo up and running on my new nrf9160 DK board, I am in the UK and could not set it up with the iBasis SIM therefore I acquired...
Hello,
I want to use UART 1 in my project (based on aws_fota sample) and I tried this code but it reboots. I cannot use the debugger (see devzone.nordicsemi.com/.../ozone...
Hi,
I am able to program the device with switch and light examples and controlling light device through switch device also done for mesh communication.
How to control...
