I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I'm working with the nrf52840 and spi mngr to talk to a SPI flash memory (AT25SF081). I use nrf_spi_mngr_perform to send a command to read the manufacturer ID
...
Hello,
I am having some trouble attempting to advertise a single custom 128bit uuid. I have two custom services sharing the same base uuid. Everything works correctly after...
I am trying to add major minor values in the ble_app_hrs example in SDK_15.3.0. I am getting an error code of 12 which is invalid data size at:
err_code = ble_advdata_encode...
Hello,
I am using SDK version15.20,pca10056,s140.
In my application I am using Bluetooth to send the data values at the rate of 750 samples per second. By sending 3 set...
Hello,
When performing serial communication using UARTE in the environment of SDK 15.3.0, SoftDevice 6.1.1, In rare cases, abnormal data is received. I don't know the cause...
Hello!
I am compiling the fiirmware for Thingy:52 (version 1.0.1), using the following link:.
https://github.com/NordicSemiconductor/Nordic-Thingy52-FW
nordicsemiconductor...
Hello All,
I've recently run into an issue with the nRF52840 Dongle where the Green channel for LD2 is not lighting up, this is a problem that is persistent across all...
Hello Nordic team,
In our project we have a requirement to write a log record to flash sector when any fault occured (hardfault or SD fault callback), so we can download...
I want to transfer data from slave to master and back to slave from master and I am doing this in the following cases: 1) Case1: Fixed connection interval and slave latency...
Hi,
I hdd developed a ble product based on nRF52810 ( SDK_15.3.0_59ac345 s112 ). I had set the connect paramter like this:
MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_1_25_MS...
Hi,
Do you have a better example than the one on nRF Cloud that can show me how to transform a HTTP GET /message from my thingy. Right now, the messages are nested and it...
While I know the 9160 does not support voice calls, I would like to know if the 9160 will accept mobile terminated (MT) data calls. If so, how is that represented in the firmware...
First of all , p lease forgive me for m y bad English if it annoys you .
I do have an interest in nRF52840 development kit, because I am trying to find a development kit...
After updating from THREAD SDK 2.0 to SDK 3.1 I am getting NRF_ERROR_NO_MEM in nrf_sdh.c.
The project is based from the multiprotocol BLE thread dynamic example.
The code...
I'm creating a ble central device that receives instructions via UART on which device to connect to and which UUID to write to.
I'm able to connect to a peripheral device...