We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi,
Lookin at this ticket https://devzone.nordicsemi.com/f/nordic-q-a/32090/qspi-pin-mux-on-nrf52840 for the nrf52840 it is said that it is ok to put QSPI on any pins (depending...
Hi,
I need to use cJson library to parse some json data. I have seen that the library is located at "nrf\ext\cjson" path. I have also seen how to add that library to a...
The documentation is VERY difficult to search. A search only goes over the chapter. I get different results depending upon which one I am in .... aarrg! And there are SOOO...
Hi,
I am not sure about the functionality of notify_cccd_handle.I am sending data from central to peripheral so the central should receive a notification from peripheral...
Very similar to this post , my use case involves cycling the modem between online and offline ("AT+CFUN=1" and "AT+CFUN=4"), for enabling GPS and also for reducing power consumption...
I am trying to broadcast an advertisement packet from a Nordic board nrf52840.
I have downloaded the latest nordic sdk and am loading the ble beacon example to the device...
Hello Nordic team, I'm currently developping a project that uses the nrf52840 as an HTTP server/client on top of its Bluetooth functionnalities.
I'm looking into implementing...
Hi,
I'm currently wprking on my project, my project it's about swarm, before the master swarm can advertise the message to the slave swarm through blehandler function now...
Hi,
My unit based on NRF52832 with SDK11 and works as pheripheral.
I started my project from nordics NUS (Nordic uart service) example.
My IOS software developer wants...
Hi Sir,
We got the nRF52833-DK, and tried to program the nRF52832 IC through the nRF52833-DK.
We download the latest version of nRF connect and command line tool, but...
Dear,
I am using THINGY:91
I am trying to read the data from BME680 sensor:
1. config: ( i used conf file from asset_tracking)
and, get the temperature:
...
Hello,
I am using UART1 to communicate with sensor. It is working fine. I can receive the data. Now I want to modify this data. When I use strcpy() function, it works properly...
Hi Team,
We are trying to make Nordic NRF52840DK board to act as a server (BLE ) where as we are trying to connect other board (Not the Nordic chip) has only transmitter...
Hello again, I accidently verified one of my own answer so I will retry.
I am currently trying to update the firmware for Thingy 52, using the NRF52 development kit. ...
I'm using a nrf52840dk as peripheral and iOS (iPhone 8) as a central. They are to be paired. The pairing routine is already implemented and works fine. The problem is that...
