Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi support team,
I've been developing a project that uses a cycling cadence sensor and interacts with my nRF52840 DK which is the central device. I merged the rscs central...
Hii
I'm using nrf5_SDK_for_Mesh_v2.0.1_src with nRF52 DK. i have tested your light switch demo by creating provisioner, proxy client and proxy server on individual NRF52...
Hello, I'm newbie developer.
I want to create a program that ends advertising when I press the button and restarts press it again.
I've seen many examples, but I can't...
Hi Team Nordic,
I know this question has been answered in several threads but the responses seem quite old now. I am using nrf52840 and SDK 15.3.0 and I want to flash...
Module : EYSHJNZWZ (nRF52832)
Is there a way to check nRF52832 IC revision? Since the chip is embedded in the module, it cannot be confirmed by appearance.
Hello,
I am working on developing a program where the nRF52840 dongle is a central device and recognized as an HID keyboard to the computer.
I played around with the peripheral...
I am trying to get a periodic interrupt every 100 uS using TIMER4. My timers_init() code sets up the TIMER4 registers as follows:
My interrupt service routine for now...
Hello
I would like to evaluate the module in a place without Cat-M \ NBIoT support
is it possible (for evaluation purposes) to send the data by other means (for example...
Hi,
New to Nordic, new to SEGGER, and new to ARM, so forgive me if I'm just missing something...
I've been asked to write new code for some boards that have the nRF51822...
I am using the SPIM example in the nRF52840 SDK. It uses SPI_INSTANCE 3. I am doing a simple SPI Write of 2 bytes.
I get SS, SCK, working properly. MOSI is transitioning...
I want to take drive code from thingy sdk and apply it to nrf5 sdk uart project, but I don't know how. Please explain in detail because i'm university student ... thank you...
Hi Team Nordic,
I am trying to save my flash data after the DFU process but it keeps on erasing it. I saw a thread in which it was explained to increase the CODE_PAGE_SIZE...
Hello,
I have a problem with app_timer.
My program need to use BLE UART for about 15 second then switch for just RADIO after.
To do so, I enable the ble stack as...
hello support team
nRF52 DK , Mesh 2.01
I am trying Experimental BLE RELAY example.
1. In first trial I am using 1 RELAY DK all works well.
2.In second Trial I am...
Hi everyone, I have a custom board using nRF52832 chip.
I want to turn ON and OFF a LED, which is directly connected to a GPIO pin.
Using this configuration I expect...
