I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I've finally completed a BLE transmission using tips about connection interval, slave latency and supervision timeout given here . I checked it with Master Control Panel app...
We are trying out nRF51822. My colleague has a top of the line Lenovo running Ubuntu and is able to detect the module when scanned. However, my macbook pro Mid 2014 (Which...
I asked this question ( devzone.nordicsemi.com/.../) to get an answer that I needed to apply for getting the Apple iBeacon certification.
Now I applied for Apple iBeacon...
I'm wondering (hoping) if there is something that I'm not doing correctly ...
We have a BLE application on the nRF51822 which has been working nicely.
It is a custom BLE...
What might be the reason that sd_softdevice_is_enabled fails? I've been programming with the S130 for some time now. And now I am in the process of adapting the bootloader...
For the S310 stack the bootloader does not set a SD_MBR_COMMAND_INIT_SD command. What needs to be done for the S130 ?
#ifndef S310_STACK
sd_mbr_command_t com = {SD_MBR_COMMAND_INIT_SD...
[PLEASE READ THE EDIT FIRST]
So, first of all, I am new to bluethoot development and I am not 100% familiar with all the inner workings of the protocol.
I am trying...
I have looked over the entire site and can not figure out what is needed to change the Smart Beacon Kit firmware and uploaded it to the beacon.
Is there a way to recompile...
Hello ,
I'm working since few days on nRF51 dongle with SofDevice S310 and most things seem to be ok.
But when I follow the System OFF and wake-up sample supplyed on GitHub...
The v3 nrf51822 and nrf51422 power efficiency was improved.
What were the improvements? How much effect should we expect to see in various operating modes. System OFF,...
In the Nordic code at this github example
there is a reference to UICR.CLEN0 .
#define CODE_REGION_1_START 0x00020000 \\
/**< This field should correspond to the size...
What is the main difference between HW controlled TWI master driver and SW controlled TWI master driver?
What is their advantages and disadvantage?
Can they switch between...
I am creating four timers in my application using app_timer.c . All timers work except the timer with ID zero never triggers.( means first timer created does not work all...
I am really struggling to get my ADXL345 SPI code working. Everything works fine on a LPC1768 and all outputs are fine on the nRF51822 Eval board, but there is no activity...
