I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello:
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hello,
I'm trying examples supplied with SDK, running on pca10006 with nRF51422 chip board and Segger J-Link debugger.
I am able to
Erase entire chip with nRFgo...
Hello,
We're creating a new design with the nRF518122 as a TWI master to two separate I2C busses. No SPI devices of any kind, so I don't think there is a resource sharing...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I need to store few variables values(long a = 4568;) to RAM (might be some other place) when the system went to sytem off mode .
How I can achieve in the nRF 51822...
Hello.
I have to detect presence of several nodes (max.8, battery supply). Addresses each of them will be known by master device. I don't have to send any data from central...
Hi,guys
In my project,I intend to generate 4 channels pwm,using 8 channel PPI,timer1,timer2. As below, the timer initializing and timer interrup handler code:
static void...
Our most advanced Bluetooth Smart SoftDevice to date released this week - S130. We're excited in a big way about this one covering as it does so many different options in...
Hello,
We would like to be able to load the s310 Softdevice via an ANT bootloader. I am using a slightly modified version of experimental_ant_bootloader from the 7.2.0 SDK...
Hi!
Is there any configuration differences between those 2 modules??
I understand from the data sheets that the pinout is just the same.
I´m testing a PA+LNA on the same...
bnjr, je veut mesurer le rssi entre deux composantes BLE Nano . quels son les fichiers .h qu'ils faut ajouter pour le faire fonctionner ?
merci a l'avance
NB : j'utilise...
I tried to program the beacon kit with the nfr51822_beacon_app.hex through DFU-OTA using the nRF Toolbox on an IPad, and though the upload seemed to work, the application...
How do I configure nRFgo to use the IAR I-jet rather than a segger? When I run nRFgo the nRF51 Programming tab is greyed out and it says no board connected. I presume this...
Hello, I use two nRF24L01+ modules as a transmitter and a receiver, and Atmega8515 as my microprocessors. The transmitter seems to be working as I can see the modulation on...