Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
board : nRF5340
sdk-nrf : v2.7.99-cs2
Zephyr version: 3.6.99
I am following https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/app_dev/bootloaders_dfu/qspi_xip_split_image...
Hello Team,
We are working on custom board using nrf54l15 platform.
If we flash only application code, it works, LED is blinking & BLE advertises. But after adding DFU...
Hello!
I'm currently working with the nRF7002 Wi-Fi chip on a custom board. The MCU used is STM32H573ZIT6, and the software is Zephyr 4.0, specifically using the Wi-Fi shell...
Hi,
i can say that i'm familiarized with nrf51 devices from some time ago.
Using softdevice 7.1.0 and MCP 3.7.1 i was able to perform a device firmware upgrade using just...
Hey I am working on nordic nRF51822, I have a doubt.
Basically I want to use it as an iBeacon and along the iBeacon payload I also want to send some services.
Is that fundamentally...
Hello,
I tried to get the bootloader dfu example with the S110 8.0 and the latest 8.0.0 SDK running but ran into tons of issues. The packet handling with KEIL is just insane...
Hello everyone!
I'm writing here becouse I'm quite new to the embedded world and I'm experiencing some troubles starting with this platform.. I must say that, since I found...
Hello,
In my application, I'm going to power the custom board with a fixed 5V connection. What is the best practice for powering the nRF51422 IC? I was thinking in using...
Hi.
We need to ring the Buzzer with 4.2kHZ PWM.
However, in the event of 4.2kHZ in nRF51822 PWM is inaccurate about 2us.
Please tell us how to fix it.
※link Very...
I use this step-by-step guide to run nrf51 Iot SDK example on nRF51822.
First I modified app_ipv6_coap_client_pca10028 such that I can run it on nRF51822.
I downloaded...
Hello Everyone,
Im using the NRF8001 for my application and was looking through the arduino SDK provided by nordic.
I want to run the device in UART mode but do not...
Hello!
I have been trying to figure out how to get the device ID/MAC address for the NRF8001, and I found the lib_aci function lib_aci_get_address() that calls a cmd event...
Hello!
I am using the nRF8001 BLE chip on the Redbear Labs Blend board, and I need to get the MAC address, which I heard is also called the device ID. I understand that...
Hi,
I am new to BLE development and I am currently using nRF51822 with the soft device S110. I am using the example ble_app_hrs that includes the ADC converter. I would like...
Hello,
The max TX power for nRF51822 is +4dBm and it corresponds to Bluetooth Class 2.
Is there a possibility to use an external amplifier to increase TX power to meet...
Hello,
I'm trying examples supplied with SDK, running on pca10006 with nRF51422 chip board and Segger J-Link debugger.
I am able to
Erase entire chip with nRFgo...
Hello,
We're creating a new design with the nRF518122 as a TWI master to two separate I2C busses. No SPI devices of any kind, so I don't think there is a resource sharing...
