Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi All !
Sorry, but I do not find answer for my question in any resources.
How to confirm indication in iOS CoreBluetooth?
If iOS work as central, in CoreBluetooth no...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
Hi all, I m new to Bluetooth Low Energy. I have to develop an indoor positioning project based on Bluetooth Low Energy 4.0 in which i have to locate person's current position...
My ble device try to notify a data to my android mobilephone after phone connect it,but sometimes,phone can't receive the data and error 8 occur .this happend frequently when...
Hi,
pstorage_raw_store() API fails as p_src address is not 4 byte aligned (i.e. 0x20002b1a), as p_src is RAM address and also as its "SOURCE" address is it necessary to...
Hey Folks
I wonder to design my own simple circuit based on NRF51422, the circuit should connect to a mobile app. By the way I'm I wonder to follow these steps:
visulaised...
Hi all,
I have one question about the deep sleep wakeup process in NRF24LE1. I want to realize the function that "when I press the button, it will cause rise edge on the...
Hi,
I'm testing doing a soft device update (v7.0 to v7.1) over DFU, but I consistently get OP_CODE_SYS_RESET sent to my device after 4 packets(80 bytes), at which point the...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
