We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi, I am evaluating the nRF51822 for an ultra low power energy harvesting application.
I measured the time from power-on (VDD applied) to code exectution (GPIO toggle)...
Is it possible to launch ipv6_coap_client on nRF51822-EK?
I have modified preproccessor simbols adding BOARD_PCA10001 instead of BOARD_PCA10028.
Also I modified part concerning...
Hi
Can anybody answer me if i do not call SOFTDEVICE_HANDLER_INIT instead i call sd_softdevice_enable ,sd_ble_enable(&enable_params),sd_nvic_EnableIRQ(SD_EVT_IRQn) directly...
I have a simple project which uses S110, so I flashed the S110 and the bin, but the result is not as expected (blinking LEDs), is there any quick way to verify before needing...
hrs_sdk7_1_bin_sc.zip contain application.bin and application.dat
How can I make a xxx.dat file?
When I del it from zip,it will cause error during dfu update.
Hello EveryOne
My button event handler is not being called. following is my code what can be the problem.
uint32_t err_code;
ble_stack_init();
timers_init...
i am working with eclipse. i want to create a binary file. after successfully creating the .elf file eclipse displays a make error saying region ram overflow by so and so...
Hello,
If I enable POFCON at 2.1V threshold in my S/W, build and download it in my target, and I turn on n51822 at VDD is 1.8V. That is, VDD is lower than POFCON threshold...
Hi ,
Could anybody share me the details on the time taken by the nRF51822 to comeout from reset state for the below reset input.
Wakeup from OFF mode reset
Pin...
Hi...
I started with S130 demo example code. Added a custom services . The problem I am having now is that after I connect ble_evt_dispatch isn't being called.
I have...
Hi, I have purchased a Nordic nRF51 and start to write my firmware using mbed OS compiler. As far as I can see the whole process was working perfectly. I could update the...
Hi,
I have a BLE peripheral with a custom service (using a different chipset). I'm working with S120 as a central, and attempting to read/write various characteristics...
I have previously bought a Evaluation kit, (now obsolete) and registered with it. I have also designed a new custom board with version 3 silicon, but I cannot download v8...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
