Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
i was trying to implement bonding in ble_app_hrs example(SDK V6.1.0 and soft device v7.0.0)
i have given params
#define SEC_PARAM_TIMEOUT 30
#define SEC_PARAM_BOND 1...
I want to use the Smart Beacon Kit (PCA20006) and the blink led demo. However it seems that I cannot use the s110 V76 softdevice when writing my app in Keil. However, how...
I'm writing an application which updates the ble advert data at run time. I use the radio_notification callback functionality. Inside that function, the code calls the ble_advdata_set...
Hi, I'm trying to run ble peripheral and timeslot receiver at the same time. I can see ble advertisements and I can connect to the peripheral. I can also read and write ble...
Hi,
Some questions below about the HID keyboard that refer to the example "/s110/ble_app_hids_keyboard" .
What initialize m_advertising_mode value before to call...
Hello,
to reduce ernergy consumption i use the sd_app_evt_wait() function while the twi is sending or receiving data.
i set nrf_twi->address and nrf_twi->txd and set...
Hello,
I have troubles using spi_master_example.
I want to control by spi a slave device from the nRF, I am sending sequences as expected and my slave device answers me...
The S130 SDS 0.5 documents a CODE_R1_BASE of 0x00020000, but I can't get it to work with code at this location. Any SoftDevice API call ends up in the application's SVC_Handler...
Hi,
i use the library app_gpiote to setup interrupts on a toggling external pin(this pin generates a signal which changes from high to low).The external interrupt signal...
Links: ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection，I don't Know how it works.The ble device call disconnection,but ble android phone respones it more then 5s...
Hi, I'm a student at Oregon State University using the nRF51 Development Kit for a project. I can't seem to find any functions for sending and recieving Bluetooth signals...
HI ALL!
I got a question about establishing my own service.
Currently, I can just send my data through the 'hrs' service(by replacing the heart_rate value with my own...
Hi,
I just downloaded the Utility app for the ble apps(nRF518 SDK) checking on my i5 at iOS 7.1.2. I have tried to connect the apps(hr, proximity) of Utility, but there is...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
