According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi!
I'm reading the PS for nRF52832 and I can't find a clear answer on the following question.
If I set up a GPIO channel with pull-up/pull-down in the PIN_CNF[n] register...
Hi, I'm learning to use the nrf52832 (PCA10040).
I'm on SDK12.2.0 S132.
I've done those basic tutorials while merging codes from the examples.
My code can currently read...
Hi, i am working on TWI sensor example in SDK11 i have connected MMa7660 to PCA10040 board as per the GIPIOs. and am integrated BLE app uart to the same TWI sensor example...
Hi,
I am using a custom board with a nrf51422, SDK11, S130 v2.0.1 with central role.
I have made changes on the code to change from MID bandwidth to High. I added the...
Hello,
I'm using the Nordic BLE-UART service found in the SDK. This is the "ble_app_uart" file in the SDK examples for the Nordic nRF51822. I'm basically sending JSON back...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make only app image for DFU.
I made a command as below refering to github.com/.../pc-nrfutil.
...
Dear all
Currently we are using version 9.0.0 (nrf51422 family---> using for 51822 chip) & now we are trying to use 12.2 ("nRF5_SDK_12.2.0_f012efa.zip").
Is there...
I've discoverd a strange behaviour with nrf51822 CEAAD00 Revision 2.
I am using NRF_POWER->SYSTEMOFF = 1; for powering down the chip and a sense signal for wakeing up....
Hi,
I have downloaded the hardware files of nrf51822 beacon kit.
How to change the pcb layout of nrf51822. ( remove the name on the pcb, change the form of the pcb etc...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
i have a strange problem which happens when i use scan mode to get 3 separate channels on saadc.
For example when i use uint32_t ticks = nrf_drv_timer_us_to_ticks...
Hi, I use Keil 5 and SDK 13.0.0 in Windows 7 64bit desktop.
I wished to test the SDK 13's BLE UART example.
However, even though I clicked "Check for Updates"...
basically i tried am trying the easiest ble example
ble_app.becon_pca10040
i tried the following.
use keil to upload into the nrf52 Evalutaion board. the led is...
Hello, i have been looking for a good development environment to use for my nrf52832 on linux. I have only found a few repositories on github pertaining to this. Not very...
Hello,
Does someone know a good J-link segger for programming the nrf51822 smart beacon kit?
And do u need a 6-pin j-link segger for the nrf51822 smart beacon kit?