Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I have tried to use sd_app_evt_wait() to sleep cpu, and use gpiote interrupt to wake up cpu from sleep.
However, gpiote interrupt cannot wake up cpu.
When I use __WFE()...
Hi,
I am trying to send sensor(accelerometer) data through beacon. I am basing my logic on the beacon example. I am putting my sensor data into an array and passing it...
Hi,
I have an nRF51 DK, found here www.nordicsemi.com/.../nRF51-DK .
I am using SDK V11.0 and S130 V2.0.
I am developing on a Linux machine.
I can compile and run...
Hi.
I'm using the Power Profiler Kit and the PPK desktop application to log the power consumption of my device. This works well for short time spans.
However, I'd also...
Hi
I'm trying to delete all files with a given file id. Will fds_file_delete() delete all files with a given file id, or just the first one it finds?
thanks
SDK1...
Hi
I'm trying to use fds_record_find() to detect if a record exists in flash storage. After erasing the device (via nrfjprog), flashing the softdevice, flashing the program...
I use an app_timer to periodically update sensor reading in my application. There is a characteristic used to change updating rate by stopping and restarting the app_timer...
Hi,
I work on a project for the nRF52832 with Keil µVision using ARM Compiler V5.06 update 2 and nRF5 SDK 11.
In a module I allocate quite some memory using malloc(...
For the BLE GAP advertising flags byte in the advertising data, we have the following options:
/**@defgroup BLE_GAP_ADV_FLAGS GAP Advertisement Flags
* @{ */
#define...
I cannot seem to save the new Device Name value in the nRF51822 beacon.
I am using the mobile app nRF Connect.
This is my procedure:
1).Run nRF Connect on Android device...
Hi Nordic Team;
I am using nrf51822 devices with sdk12.3.0. I am using buttonless dfu example without any problem with sdk12.3. However, I see that you realese sdk14 that...
We're considering nRF51/52 to implement a specific BLE application. We need the nRF51/52 go to sleep if a BLE collision signal or interference on an advertising channel has...
Hi,
I'm using nRF5_SDK_13.0 on nRF52840 based on ble_app_hrs_rscs_relay example. I use it to connect a bluetooth 4.0 device and it's ok now. Also I have a bluetooth 5.0...
Hello, our device is able to be used by Iphone and Andriod. For the ANCS, we have tested the Iphone and it is OK. However, Andriod notification does not need the ANCS. As...
