Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
hi
I have designed a small PCB with the NRF52 chip on it and kept few ports for some peripherals. Apart from that I only have 4 pins that I can connect to, UART-Tx, UART...
Hello,
I'm wondering if my nRF DK51 is not broken as it behaves quite strange when trying to connect with a BLE Central (iOS and Android devices). For most of the part...
I am trying to track down a power usage problem with my code. When I started using SDK 13.0.0/S140 v5.0.0-2.alpha on a PCA10056, the power usage went up in my app. I see that...
I'll try to simplify my project as much as possible to make this understandable.
I'm wiring an nRF52 PCA10040 board to an iCE5LP (Lattice) FPGA.
I'm having an issue with...
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon . It should act as an NRF51 USB dongle (pca10031-like) but...
My pc server should send information to nrf52832 by ECDH, then I create a dll file from micro-ecc. However,the result in windows is not the same as the result in nrf52832...
dear friends ,
within a peripheral connection event, 9 states is identified, as it is shown in the pic above(from s132 document). Can i get a detailed description about what...
Hi @ all,
I am working with IoT SDK 0.9 and nRF52DK.
I have trouble with the lwIP CoAP client example.
Everything works so far, the board is connected and I'm able...
Hello! I am using a custom board that contains a nRF52832 device. The board has the SWDIO and SWDCK lines connected, which I have successfully been using to flash and debug...
I'm migrating to the new 13.0.0 SDK and I'm wondering what are the benefits of using nrf_serial over app_uart (if any) and what steps I would need to take to switch over if...
I have successfully manged to achieve serial communication between my PC (Windows) and nRF52 board by using the pc-ble-library and the pc-ble-library-js .
I can run without...
Hi, I updated nrfutil to use in new sdk 13, but when I type "nrfutil pkg generate --help" I can't see the code for Softdevice S132 v4.0.2 (0x98) as indicated in this guide...
I have done erase all thing.
But in the second step, I am getting following error.
nrfjprog --program s132_nrf52_3.0.0_softdevice.hex
ERROR: The --family option given...
Hello,
I'm following the steps listed in the nRF5_IoT_SDK documentation and would like to connect the nRF52 to my Raspberry Pi 3 router. I have the RPi3 enabled for 6LowPan...
