after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I want send out 6 notification in one connection interval. But now I only see 3 packets in my sniffer. So I want to know how to achieve this goal?
This picture is captured...
I'm using nRF51(822) with S130.
I registered my event handler with:
softdevice_ble_evt_handler_set(ble_evt_dispatch);
In my main loop, I call sd_app_evt_wait(); ...
Dear,all
device:51822 s110 sdk8.1.0 adverting interval:1s
or exmaple hrm s110 PCA10005
i use moto Z phone and nrf connect apk,it is difficult to receive
the advertise...
Hi, I have created a custom PCB (FR4, 4-layered) which uses nRF52832-QFAA.
This PCB uses the λ/4 printed monopole antenna .
I wish to measure the RSSI value of this...
hi,all
i use sniffer.exe(ble-sniffer_win_1.0.1_1111_Sniffer),and sniffer connection data,the sniffer.exe often automatically quit.
the sniffer pcb is not nordic.
anormal...
Hi,
Instead of initiating the DFU library in Android with an address is it possible to handover a existing GATT connection to a device already in DFU mode?
We have cases...
Hi,
I try to add support of dfu in our appl. In documentation I could not find info about softdevice size which should be provided in start packet. It looks like I should...
Hi,all
SDK:8.1.0 51822
S7 Edge（android V7.0）
i use the sumsung S7 Edge and the oppo R9S connect with my device,nRF Connect is often note:
GATT_CONN_TERMINATE_LOCAL_HOST...
for ble_app_ancs_c_s130_pca10028 example of sdk11,s130 version 2.0.0
The preferred RAM,ROM and UUID COUNT is shown below
FLASH (rx) : ORIGIN = 0x0001B000, LENGTH = 0x25000...
Hi All
I am trying to build hex file using eclipse id on Mac. everything looks ok, as it eclipse build file without any error but its not working on nrf52 dk.
before...
Now I’m using nRF51822 with S130 SoftDevice.
There are two kinds of devices which is just for scan(A) – 20EA and both scan and advertising(B) - 2EA.
I found that B just...
Hi,
My question is similar to this devzone.nordicsemi.com/.../ but I can't get it to work.
I am using SEGGER_RTT_WriteString and sprintf for debugging, but I am not able...
Our mobile app is currently running atop of easyble and nordicble.js/Cordova. This library works great on all Apple devices, however, Bonding with Android devices of various...
We have done a custom PCB believing that we could use P0.0 as analog input. Now we kind of found out that we cannot, and will change the PCB design. Given that we already...
