Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
I've recently tried add App Data (pstorage) to my Application. Thus I want to preserve this data over DFU Updates. To do this I updated my Bootloader to reserve App Data during...
Hi
I am using SDK11 with S130, NRF51822 that using ANCS and facing bonding problems after reach the max bonds.
Reference to nRF51-ble-peripheral-bond-handling example,
...
My application is doing kind of old communication with an old machine.
Communication line is bit banged by an GPIO. Baud rate is 0.5ms.
"Start bit" is still used to synchronized...
Hi,
I use nRF52832 with sdk 12.2.
and I running the ble_app_hrs_c example code on pca10040 evb.
I can scan many hr devices but polar h7 heart rate not.
I check Iphone...
Hi I use nRF52832 and move my project to SDK13.
I want to use debug mode in keil-c and try to find after ble_db_discovery_start function call why no csc_c_evt_handler_t call...
I'm working on an OTA firmware update process, using my own bootloader and application. To understand the process' limitations, I need to know to what extent one can update...
hello everyone：
how many timers can i open in nrf51822(QFAA) with SDK9.0? the APP_TIMER_MAX_TIMERS's max value
#define APP_TIMER_MAX_TIMERS 13 /**< Maximum number of...
Hello,
I am referring to this link
www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules
and I am referring to Xuntong PTR5518 11 15x15x2mm PCB China product...
I see BLE_GAP_EVT_SEC_PARAMS_REQUEST generated from SD. How to call this request for pairing state?
I can't find any peer manager in the project.
Explane, pls.
Following is a simple application that I have created. It has no softdevice and the configuration is very similar to blinky freeRTOS example.
Source code:
main.c
...
Hello ,
I'm working on custom board, I'm trying to disconnect from the Central (Andriod app) when the battery is below certain level and stop re-advertising.
Below is...
In s130 Soft device v2.0 document, it says it can have role with up to 8 Role concurrent with Central, Pheripheral, Advertiser, Observer.
I'm not sure i've understand all...
Hello. I'm using nRF52832, PCA10040, SDK13, S132 and "ble_app_uart" as reference.
When I connected board through by bluetooth, I couldn't see notification message which...
Hello,
According to the nRF Sniffer Guide 1.2, the sniffer is supported on a number of platforms (nRF51822/nRF51422 Evaluation Kits and others). All of them (as far as...
I am working on a project where my nrf51822 is on for long periods of time in lower power mode. Yesterday I made some updates to the code and the devices were working fine...
