I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi. I'm using nRF51822AC, SDK12.2.0.
I just started trying priphral function which provides multi link(Max. 8 links).
Which example code can I refer?
I hope your...
I have a scenario in which hundreds of beacons are advertising. I want to know whether an observer can observe all the beacons or not. I have done a lot of search on this...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello!
I'm having trouble adding vendor specific UUID and configuring the memory. My service will require 3 vendor specific 128 bit UUID. One for the service and two for...
Hello,
I would like to make use of an Adafruit sensor Adafruit_TSL2591 connected to my nrf52 through the TWI interface. I have seen the example TWI master device, in that...
Hi,
My apology if this question has been answered. I wonder if >2mA current draw for an APP with the following design considered normal consumption?
Custom GATT profile...
Hi,
I'm using the UART to talk to a radio module with sdk 12.1 on nrf52.
I'm seeing frequent UART errors, where the event handler is called with event type APP_UART_COMMUNICATION_ERROR...
Some of you may be using the ARM compiler that Nordic provides with SDK 13.0. I was not able to install it on my PC as it does not want to install since it sees another other...
SDK 13.0.0
nrf_soc_nosd/nrf_nvic.h has this header guard:
#ifndef NRF_SOC_H__
#define NRF_SOC_H__
This means you couldn't include nrf_soc.h after including nrf_nvic...
Hello,
I'm using TIMER1 to generate a timer compare event. I connect the event with the sample task of the saadc like in the saadc example from the SDK. Everything works...
Hi,
While using the JLinkExe along with the JLinkRTTClient the RTT client eventually stops outputting messages.
After that, both the JLinkExe and the nrfjprog output...
Thank you for the support so far.
I want to ask that if for example in your system or product we want to add bluetooth headphone feature which support Bluetooth 4.0 headphones...
Hi,
I am new to Nordic product and I have NRF52 DK. I have started reading this document
www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit
However...
Hi,
I am trying to use the BLE v4.2 extended data length on the NRF51822 but the S130 doesn't seem to support it. Please can anyone let me know if it is supported with...
Hi,
I am trying to measure (and reduce) the current consumption of my board. I am using nrf52832 (64K RAM) for my development. The RAM layout is as follows: RAM (rwx) : ORIGIN...
