Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello sir,
I am using nRF52832 board and interface with 3 axis accelerator reading ADC for 3 Channel. I have use sample code for controlling in timer/RTC mode. My ADC is...
Hi,
I'm doing some measurement on the radio peripheral of the nRF52840 using the generated events and a timer which is set to run at 16MHz. Radio events and Start/Capture...
SDK version: 13.1
Hardware: nRF52832
Eclipse version: link text (I could not get the marketplace working in the latest Mars Eclipse version, so I downloaded this version...
I am evaluating the sdk14 ble_app_uart example. I am able to run this code and connect to this uart service but do not see messages get passed to the uart pin. Only when I...
I am using a nrf52832 Development Board with s132 for some BLE applications. I developed a beacon app, set for BLE peripheral, and every reading of the advertising from this...
Hi,
I'm using NRF51 DK board and i am following characteristic tutorial available. I am able to send temperature value over Bluetooth by using light blue app.. Instead of...
I am using nRF connect to debug an application on a nRF52832. When I perform a scan, I can see the UUID of the nRF52832 device I want to connect to. Where is this UUID stored...
Hi,
I'm unable to auto connect with nrf51 using nrf Connect App, if I select Connect using Auto-connect only and no Bonding in nrf Connect App for first time.
With Auto...
Hello,
i have a question about the range. I have a Bluetooth-Module with nRF52832. I tested it in my Office. Additional I can Change the Output power from +4 dBm to 0 dBm...
My use case involves buttonless beacons that should only be connected to by authenticated users on their mobile device (Android / iOS).
Once connected, these beacons will...
Hi,
I have Nordic NRF52 DK. What chip does it have? because there are quite many chips of NRF52 series and can you also tell me about the PCB reference design of the chip...
According to the PDM of the nRF52810 datasheet，the input of the filter is the two-channel PDM serial stream (with left channel on clock high, right channel on clock low),...
I am looking at a Bosch GLM50C and when i connect with nrf connect on IOS I can only see device information and a custom service, on android I can also see the generic access...
Hi,
I want to confirm two points in the PCB layout of nRF52:
In the data sheet and in the reference circuits section, there are no caps on pins 37 and 38 (QFN...
