I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
NRF52832 S132 MPU6050 TWI
I want to finish the function:
When the ACC, GYRO data update, the INT pin to generate an interrupt, and then in the P026 pin configuration...
Hi,
I have the Nordic Thingy:52 (PCA20020 1.0.0 2017.19). It worked well until I downloaded new version of firmware 1.1.0 and updated Thingy. After that I didn't see advertising...
I want to use the UICR customer registers to store MAC/serialization information for my devices. It looks like the UICR customer section would be great, and the product spec...
I want to use whitelist in Central (nrf51822,SDK12),but I don't know which function to add the MAC address.
These three functions：
peer_list_get(pm_peer_id_t * p_peers...
Hi,
With S132 it is possible to advertise on specific channel.
See devzone.nordicsemi.com/.../
But, since from BLE5 advertisement can be done on any of the 40 channels...
Hardware: redbearlabs Nano V2 (see pinout below)
Programmer: DAPLink v1.5 supplied by redbear
IDE: Arduino with the redbearlab nano 2 board package
The schematic can...
I'm writing an Android application that connects to various BLE peripherals including the NRF51 and NRF52. I don't know if this question is appropriate for this site, but...
Hi,
we are trying to disable 2 of 3 advertising channels on nRF52832 SoC with the softdevice S132 (1.0.0-3.alpha) installed. The example project ble_app_beacon works well...
hi
I am using ESB_DPL protocol between 51822 and 24LE1, and i used the sdk 12.2 examples/proprietary_rf/esb_ptx.
In my case, 51822 sent some packages with PTX mode,...
Hi,
I am interested to hear if anybody knows if it's possible to use 6LoWPAN on an iOS device together with nRF52832 ? I tried searching online but have not got any hits...
Hello,
I'm working on an application where we have a number of sensors and a radio that each require a connection to the nRF52. Specifically, 4 of these peripherals need...
DFU & UICR works well. However, concerning sw protection, we found that the binary file in the ZIP package of DFU is open to access. That is a security breach. Is any solution...
I have started to implement bootloader for 52832 and checked out "Secure DFU Serial" example from SDK v13.0 with Segger Embedded Studio.
I checked out this question devzone...
Our current project (custom nrf52 board SDK12.2) is set up as a peripheral device with the phone being the central device. This nrf52 device is plugged in and power consumption...
