Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
Hi,
I use bootloader from SDK6 and I have sd_power_system_off() in on_ble_evt in event BLE_GAP_EVT_TIMEOUT and BLE_GAP_EVT_DISCONNECTED. I use SDK7.1 and SD110 7.1.
It cause...
I'm programming an application that uses the NUS, and I'm trying to test my code using the Android version of nRF Connect. I'm using a nRF52832 on dev board PCA10040, and...
Hello,
With sdk13 and app_pwm library, I only got 9bits resolution for 32KHz freq.
The pwm should have 16bits resolution, with max freq 100KHz?
please could anyone...
hi ,all
I feel confused about" out_of_sync" and" in_sync" parameters .If a devece is in sync,how the channels was changed ?And what's the use of"nrf_gzll_set_device_channel_selection_policy...
we builded " BLE to IR " using nRF51822 , it was working fine with out the softdevice.
problem start when we integrated with the SoftDevice .
1.the problem that we need...
Hi.
I am trying to get a capacitive sensor library using a button ( 2 plates, one to ground, one to the AIN, separated).
It's going crazy, sometimes it just get tones...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
