Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
when a particular line of my code is at line 54, the following compile error occurs:
error: #101: "assert_line_54" has already been declared in the current scope
line...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
hello,
On a device with nRF51822-CEAA packaged in a ISP130301, we have a problem with RSSI value measurement.
We use Master control panel and bluetooth usb key provide...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
nrf51822QfAC
S130 stack was working fine and ble_app was able run successfuly able to see the ble on the app;
Now after few days now facing issue in running the same code...
having issue with nrf51822
nrf51822 breakup board was running fine with S130 2.0 stack and ble_app_uart
Now facing issue such that when softdevice enabled is called the...
Hi,
I just switch to Embbeded Studio following the last tutorial ( here ).
I'm working on NRF51822 with SDK12 and TWI_sensor example (without SoftDevice). I followed...
I see from the release notes of s132 4.0.0-2.alpha that it adds:
Support for 20 links in total with freely selectable role (Central/Peripheral) for each link.
I want...
Hey,
I am trying to control an external LED using two nRF52832 boards. I am using "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\experimental_ble_app_blinky" code for...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
